- 您現在的位置：買賣IC網 > PDF目錄10264 > MAX9750BETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF資料下載
參數資料
| 型號： | MAX9750BETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | AB 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.6W x 2 @ 3 歐姆; 110mW x 2 @ 16 歐姆 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 特點： | 消除爆音，短路保護和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MAX9750/MAX9751/MAX9755
2.6W Stereo Audio Power Amplifiers and
DirectDrive Headphone Amplifiers
14
______________________________________________________________________________________
parasitic bond wire and trace inductance. Although not
typically required, additional high-frequency ripple atten-
uation can be achieved by increasing the size of C2 (see
the
Block Diagrams).
Headphone Sense Input (HPS)
The headphone sense input (HPS) monitors the head-
phone jack and automatically configures the device
based upon the voltage applied at HPS. A voltage of
less than 0.8V sets the device to speaker mode. A volt-
age of greater than 2V disables the bridge amplifiers
and enables the headphone amplifiers.
For automatic headphone detection, connect HPS to the
control pin of a 3-wire headphone jack as shown in
Figure 5. With no headphone present, the output imped-
ance of the headphone amplifier pulls HPS low. When a
headphone plug is inserted into the jack, the control pin
is disconnected from the tip contact and HPS is pulled
to VDD through a 10A current source.
BIAS
The MAX9750/MAX9751/MAX9755 feature an internally
generated, power-supply independent, common-mode
bias voltage of 1.8V referenced to GND. BIAS provides
both click-and-pop suppression and sets the DC bias
level for the amplifiers. Choose the value of the bypass
capacitor as described in the
BIAS Capacitor section.
No external load should be applied to BIAS. Any load
lowers the BIAS voltage, affecting the overall perfor-
mance of the device.
Gain Selection
MAX9750
The MAX9750 features an internally set, selectable gain.
The GAIN1 and GAIN2 inputs set the maximum gain of
the MAX9750 speaker and headphone amplifiers (Table
1). The gain of the device can vary based upon the volt-
age at VOL (see the
Analog Volume Control (VOL) sec-
tion). However, the maximum gain cannot be exceeded.
MAX9751/MAX9755
The gain of the MAX9751/MAX9755 is set by the GAIN
input. Driving GAIN high sets the gain of the speaker
amplifiers to 9dB and the gain of the headphone ampli-
fiers to 0dB. Driving GAIN low sets the gain of the
speaker amplifiers to 10.5dB, and the gain of the head-
phone amplifiers to 3dB (Table 2).
Analog Volume Control (VOL)
The MAX9750 features an analog volume control that
varies the gain of the device in 31 discrete steps based
upon the DC voltage applied to VOL. The input range of
VVOL is from 0 (full volume) to 0.858 x HPVDD (full mute),
with example step sizes shown in Table 3. Connect the
reference of the device driving VOL (Figure 6) to HPVDD.
Since the volume control ADC is ratiometric to HPVDD,
any changes in HPVDD are negated. The gain step sizes
are not constant; the step sizes are 0.5dB/step at the
upper extreme, 2dB/step in the midrange, and 4dB/step
at the lower extreme. Figure 7 shows the transfer function
of the volume control for a 3.3V supply.
ADDITIONAL THD+N DUE
TO DC-BLOCKING CAPACITORS
FREQUENCY (Hz)
THD+N
(%)
10k
1k
100
0.001
0.01
0.1
1
10
0.0001
10
100k
TANTALUM
ALUM/ELEC
Figure 4. Distortion Contributed by DC-Blocking Capacitors
MAX9750/
MAX9751/
MAX9755
10
μA
1k
Ω
1k
Ω
20
14
13
VDD
HPS
HPOUTL
HPOUTR
SHUTDOWN
CONTROL
Figure 5. HPS Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2ND-MY | CONVERTER MOD DC/DC 85V 50W |
| MAX9750CETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| VE-230-CU-F1 | CONVERTER MOD DC/DC 5V 200W |
| VE-2NB-MY | CONVERTER MOD DC/DC 95V 50W |
| MAX9705CEBC+T | IC AMP AUDIO PWR 2.3W D 12UCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9750BEUI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9750CETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9750CETI+C2U | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9750CETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9750CEUI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。