- 您現在的位置：買賣IC網 > PDF目錄2091 > MAX9742ETX+ (Maxim Integrated Products)IC AMP AUDIO PWR 20.5W D 36TQFN PDF資料下載
參數資料
| 型號： | MAX9742ETX+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/36頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 20.5W D 36TQFN |
| 標準包裝： | 50 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 20.5W x 2 @ 8 歐姆 |
| 電源電壓： | 20 V ~ 40 V，±10 V ~ 20 V |
| 特點： | 消除爆音，差分輸入，靜音，短路和熱保護，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MAX9742
Single-/Dual-Supply, Stereo 16W,
Class D Amplifier with Differential Inputs
18
______________________________________________________________________________________
Summing Configuration (Audio Mixer)
Figure 6 shows the MAX9742 configured as a summing
amplifier, which allows multiple audio sources to be lin-
early mixed together. Using this configuration, the out-
put of the MAX9742 is equal to the weighted sum of the
input signals:
As shown in the above equation, the weighting or
amount of gain applied to each input signal source is
determined by the ratio of RF and the respective input
resistor (RIN1, RIN2, RIN3) connected to each signal
source. Select RF and RIN_ so that the dynamic range
of the MAX9742 is not exceeded when the input signals
are at their maximum values and in phase with each
other (see the
Output Dynamic Range section).
To minimize output offset voltages due to input bias
currents, connect a resistor, ROS, (see Figure 6)
between IN_+ and MID. Select the value of ROS such
that the DC resistances looking out of inputs of the
amplifier (IN_+ and IN_-) are equal. For example, when
using the dual-supply configuration with a DC-coupled
input source, the value of ROS should be equal to
RF||RIN1||RIN2|| ||RINn.
Mono Bridge-Tied-Load (BTL)
Configuration
The MAX9742 also accommodates a mono bridge-tied-
load (BTL) configuration that can be used in single-
supply and dual-supply applications. In the BTL
configuration, the speaker load is driven differentially
by connecting the half-bridge outputs as a full H-bridge
driver. To drive the speaker differentially, the inputs of
both channels must be driven by the same audio signal
with one channel 180° out-of-phase with the other
channel. Figure 7 shows the connections required for
BTL operation.
The advantages of BTL operation include reduced
component count due to the elimination of the output-
coupling capacitors when using single-supply opera-
tion, a 6dB increase in gain due to the load being
driven differentially, increased output power into a sin-
gle load, and the minimization of the supply-pumping
since each half bridge is driven 180° out-of-phase (see
the
Supply Pumping Effects section). For single-supply
applications, the output-coupling capacitors are not
needed for BTL operation since the DC voltage present
at each half-bridge output is equal in value and applies
to each side of the load. This means no DC voltage
appears across the load, and therefore, no DC current
flows into the speaker.
V
(V
R
V
R
V
R
)
OUT_
IN1
F
IN1
IN2
F
IN2
IN3
F
IN3
=
++
OUT_
VIN2
CIN
RIN2
ROS
MAX9742
VIN1
CIN
RIN1
VIN3
CIN
RIN3
MID
TO CLASS D
MODULATOR
RF
IN_-
IN_+
CFB_
FB_
VOUT_ (VIN1
RF
× VIN2
RF
× VIN3
RF
)
RIN1
RIN2
RIN3
Figure 6. Summing Amplifier Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9744ETH+ | IC AMP AUDIO PWR 22.5W D 44TQFN |
| MAX9753ETI+T | IC AMP AUDIO PWR 2.2W D 28TQFN |
| MAX9755ETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MAX9758ETJ+T | IC AMP AUDIO PWR 2.3W AB 32TQFN |
| MAX9759ETE+T | IC AMP AUDIO PWR 3.2W D 16TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9742ETX+ | 功能描述:音頻放大器 Stereo 16W Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9742ETX+T | 功能描述:音頻放大器 Stereo 16W Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9742EVKIT+ | 功能描述:音頻放大器 Evaluation Kit for the MAX9742 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9744ETH+ | 功能描述:音頻放大器 Stereo 20W Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9744ETH+T | 功能描述:音頻放大器 Stereo 20W Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。