- 您現在的位置：買賣IC網 > PDF目錄10343 > MAX9723AEBE+T (Maxim Integrated Products)IC AMP AUDIO .06W STER AB 16UCSP PDF資料下載
參數資料
| 型號： | MAX9723AEBE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/25頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO .06W STER AB 16UCSP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | AB 類 |
| 輸出類型： | 耳機，2-通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 60mW x 2 @ 16 歐姆 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 特點： | 低音增強模式，消除爆音，I²C，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 16-UCSP（2x2） |
| 封裝/外殼： | 16-WFBGA，CSPBGA |
| 包裝： | 帶卷 (TR) |
MAX9723
the headphone. The MAX9723A and MAX9723B have a
maximum amplifier gain of 0dB while the MAX9723C
and MAX9723D have a maximum gain of +6dB.
Amplifier volume is digitally programmable to any one
of 32 levels.
DirectDrive
Traditional single-supply headphone amplifiers have
their outputs biased at a nominal DC voltage, typically
half the supply, for maximum dynamic range. Large cou-
pling capacitors are needed to block this DC bias from
the headphone. Without these capacitors, a significant
amount of DC current flows to the headphone, resulting
in unnecessary power dissipation and possible damage
to both headphone and headphone amplifier.
Maxim’s DirectDrive architecture uses a charge pump to
create an internal negative supply voltage. This allows
the MAX9723 headphone amplifier outputs to be biased
at 0V, almost doubling the dynamic range while operat-
ing from a single supply. With no DC component, there is
no need for the large DC-blocking capacitors. Instead of
two large (typically 220F) tantalum capacitors, the
MAX9723 charge pump requires only two small 1F
ceramic capacitors, thereby conserving board space,
reducing cost, and improving the low-frequency
response of the headphone amplifier. See the Output
Power vs. Charge-Pump Capacitance and Load
Resistance graph in the Typical Operating Characteris-
tics for details of the possible capacitor sizes.
In addition to the cost and size disadvantages, the DC-
blocking capacitors required by conventional head-
phone amplifiers limit low-frequency response and can
distort the audio signal.
Previous attempts at eliminating the output-coupling
capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raises some issues:
1) The sleeve is typically grounded to the chassis.
Using the midrail biasing approach, the sleeve must
be isolated from system ground, complicating prod-
uct design. The DirectDrive output biasing scheme
allows the sleeve to be grounded.
2) During an ESD strike, the amplifier’s ESD structure is
the only path to system ground. The amplifier must
be able to withstand the full ESD strike. The
MAX9723 headphone outputs can withstand an
±8kV ESD strike (HBM).
3) When using the headphone jack as a line out to
other equipment, the bias voltage on the sleeve may
conflict with the ground potential from other equip-
ment, resulting in possible damage to the amplifiers.
The DirectDrive outputs of the MAX9723 can be
directly coupled to other ground-biased equipment.
Charge Pump
The MAX9723 features a low-noise charge pump. The
600kHz switching frequency is well beyond the audio
range, and does not interfere with the audio signals.
This enables the MAX9723 to achieve a 99dB SNR. The
switch drivers feature a controlled switching speed that
minimizes noise generated by turn-on and turn-off tran-
sients. Limiting the switching speed of the charge
pump minimizes di/dt noise caused by the parasitic
bond wire and trace inductance. Although not typically
required, additional high-frequency noise attenuation
can be achieved by increasing the size of C2 (see the
Functional Diagram/Typical Operating Circuit).
Shutdown
The MAX9723 features a 5A, low-power shutdown
mode that reduces quiescent current consumption and
extends battery life. Shutdown is controlled by a hard-
ware or software interface. Driving
SHDN low disables
the drive amplifiers, bias circuitry, charge pump, and
sets the headphone amplifier output impedance to
20kΩ. Similarly, the MAX9723 enters shutdown when bit
seven (B7) in the control register is reset.
SHDN and B7
must be high to enable the MAX9723. The I2C interface
is active and the contents of the command register are
not affected when in shutdown. This allows the master
to write to the MAX9723 while in shutdown.
Stereo DirectDrive Headphone Amplifier
with BassMax, Volume Control, and I2C
10
______________________________________________________________________________________
VDD
+VDD
-VDD
VDD/2
GND
SGND
CONVENTIONAL AMPLIFIER BIASING SCHEME
DirectDrive BIASING SCHEME
Figure 1. Traditional Amplifier Output vs. MAX9723 DirectDrive
Output
相關PDF資料 |
PDF描述 |
|---|---|
| MS3126F18-32SWLC | CONN HSG PLUG 32POS STRGHT SCKT |
| MAX9711ETC+ | IC AMP AUDIO PWR 3W MONO 12TQFN |
| D38999/20FE8BN | CONN HSG RCPT 8POS WALL MT SCKT |
| MS27484T18B66SLC | CONN HSG PLUG 66POS STRGHT SCKT |
| D38999/20MD18BA | CONN HSG RCPT 18POS WALL MT SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9723AETE | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX9723AETE+ | 功能描述:音頻放大器 Stereo DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9723AETE+T | 功能描述:音頻放大器 Stereo DirectDrive Headphone Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9723AETE-T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| MAX9723AEUP | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。