- 您現在的位置：買賣IC網 > PDF目錄2091 > MAX9714ETJ+T (Maxim Integrated Products)IC AMP AUDIO PWR 8W STER 32TQFN PDF資料下載
參數資料
| 型號： | MAX9714ETJ+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/18頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 8W STER 32TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 8W x 2 @ 16 歐姆 |
| 電源電壓： | 10 V ~ 25 V |
| 特點： | 消除爆音，差分輸入，靜音，短路和熱保護，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 32-TQFN-EP（7x7） |
| 封裝/外殼： | 32-WQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
MAX9713/MAX9714
is very small. Although this movement is small, a speak-
er not designed to handle the additional power can be
damaged. For optimum results, use a speaker with a
series inductance > 30H. Typical 8 speakers exhibit
series inductances in the range of 30H to 100H.
Optimum efficiency is achieved with speaker induc-
tances > 60H.
Gain Selection
Table 2 shows the suggested gain settings to attain a
maximum output power from a given peak input voltage
and given load.
Internal Regulator Output (VREG)
The MAX9713/MAX9714 feature an internal, 6V regula-
tor output (VREG). The MAX9713/MAX9714 REG output
pin simplifies system design and reduces system cost
by providing a logic voltage high for the MAX9713/
MAX9714 logic pins (G_, FS_). VREG is not available as
a logic voltage high in shutdown mode. Do not apply
VREG as an input voltage high to the MAX9713/
MAX9714 SHDN pin. Do not apply VREG as a 6V poten-
tial to surrounding system components. Bypass REG
with a 6.3V, 0.01F capacitor to GND.
Output Offset
Unlike a Class AB amplifier, the output offset voltage of
Class D amplifiers does not noticeably increase quies-
cent current draw when a load is applied. This is due to
the power conversion of the Class D amplifier. For
example, an 8mV DC offset across an 8 load results
in 1mA extra current consumption in a Class AB device.
In the Class D case, an 8mV offset into 8 equates
to an additional power drain of 8W. Due to the high
efficiency of the Class D amplifier, this represents an
additional quiescent current draw of: 8W/(VDD/100 η),
which is on the order of a few microamps.
Input Amplifier
Differential Input
The MAX9713/MAX9714 feature a differential input struc-
ture, making them compatible with many CODECs, and
offering improved noise immunity over a single-ended
input amplifier. In devices such as PCs, noisy digital sig-
nals can be picked up by the amplifier’s input traces.
The signals appear at the amplifiers’ inputs as common-
mode noise. A differential input amplifier amplifies the
difference of the two inputs, any signal common to both
inputs is canceled.
Single-Ended Input
The MAX9713/MAX9714 can be configured as single-
ended input amplifiers by capacitively coupling either
input to GND and driving the other input (Figure 5).
Component Selection
Input Filter
An input capacitor, CIN, in conjunction with the input
impedance of the MAX9713/MAX9714, forms a high-
pass filter that removes the DC bias from an incoming
signal. The AC-coupling capacitor allows the amplifier
to bias the signal to an optimum DC level. Assuming
zero-source impedance, the -3dB point of the highpass
filter is given by:
Choose CIN so f-3dB is well below the lowest frequency
of interest. Setting f-3dB too high affects the low-fre-
quency response of the amplifier. Use capacitors
whose dielectrics have low-voltage coefficients, such
as tantalum or aluminum electrolytic. Capacitors with
high-voltage coefficients, such as ceramics, may result
in increased distortion at low frequencies.
Charge-Pump Capacitor Selection
Use capacitors with an ESR less than 100m for opti-
mum performance. Low-ESR ceramic capacitors mini-
mize the output resistance of the charge pump. For
best performance over the extended temperature
range, select capacitors with an X7R dielectric.
f
RC
-3dB
IN IN
1
2
=
π
6W, Filterless, Spread-Spectrum
Mono/Stereo Class D Amplifiers
10
______________________________________________________________________________________
Table 2. Gain Settings
GAIN (dB)
DIFF INPUT
(VRMS)
RL (
)
POUT
at 10%
THD+N (W)
13.0
1.27
16
8
16.1
0.89
16
8
19.1
0.63
16
8
22.1
0.45
16
8
13.0
0.78
8
6
16.1
0.54
8
6
19.1
0.39
8
6
22.1
0.27
8
6
MAX9713/
MAX9714
IN+
IN-
0.47F
SINGLE-ENDED
AUDIO INPUT
Figure 5. Single-Ended Input
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9715ETE+T | IC AMP AUDIO PWR 2.8W D 16TQFN |
| MAX9716EUA+T | IC AMP AUDIO PWR 1.4W MONO 8MSOP |
| MAX9718DEUB+ | IC AMP AUDIO PWR 1.4W AB 10MSOP |
| MAX97200AEWC+T | IC HEADPHONE AMPLIFIER 12WLP |
| MAX9720AEUE+T | IC AMP AUDIO .05W STER 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9714EVKIT | 功能描述:音頻放大器 Evaluation Kit for the MAX9704 MAX9714 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9715ETE+ | 功能描述:音頻放大器 2.8W Low-EMI Stereo Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9715ETE+T | 功能描述:音頻放大器 2.8W Low-EMI Stereo Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9715EUE+ | 制造商:Maxim Integrated Products 功能描述:AUD AMP SPKR 2CH STEREO 2.8W CLS-D 16TSSOP - Rail/Tube |
| MAX9715EUE+T | 制造商:Maxim Integrated Products 功能描述:AUD AMP SPKR 2CH STEREO 2.8W CLS-D 16TSSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。