- 您現在的位置：買賣IC網 > PDF目錄10459 > MAX9708ETN+D (Maxim Integrated Products)IC AMP AUDIO PWR 42W STER 56TQFN PDF資料下載
參數資料
| 型號： | MAX9708ETN+D |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 42W STER 56TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 37 |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道）或 2-通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 42W x 1 @ 4 歐姆; 21W x 2 @ 8 歐姆 |
| 電源電壓： | 10 V ~ 18 V |
| 特點： | 消除爆音，差分輸入，靜音，短路和熱保護，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 56-TQFN-EP（8x8） |
| 封裝/外殼： | 56-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
| 產品目錄頁面： | 1392 (CN2011-ZH PDF) |
MAX9708
20W/40W, Filterless, Spread-Spectrum,
Mono/Stereo, Class D Amplifier
14
Maxim Integrated
Linear Regulator (REG)
The supply voltage range for the MAX9708 is from 10V
to 18V to achieve high-output power. An internal linear
regulator reduces this voltage to 6.3V for use with
small-signal and digital circuitry that does not require a
high-voltage supply. Bypass a 0.01F capacitor from
REG to GND.
Applications Information
Logic Inputs
All of the digital logic inputs and output have an
absolute maximum rating of +12V. If the MAX9708 is
operating with a supply voltage between 10V and 12V,
digital inputs can be connected to PVDD or VDD. If
PVDD and VDD are greater than 12V, digital inputs and
outputs must connected to a digital system supply
lower than 12V.
Input Amplifier
Differential Input
The MAX9708 features a differential input structure,
making them compatible with many CODECs, and
offering improved noise immunity over a single-ended
input amplifier. In devices such as flat-panel displays,
noisy digital signals can be picked up by the amplifier’s
inputs. These signals appear at the amplifiers’ inputs as
common-mode noise. A differential input amplifier
amplifies only the difference of the two inputs, while any
signal common to both inputs is attenuated.
Single-Ended Input
The MAX9708 can be configured as a single-ended
input amplifier by capacitively coupling either input to
GND and driving the other input (Figure 4).
Component Selection
Input Filter
An input capacitor, CIN, in conjunction with the input
impedance of the MAX9708, forms a highpass filter that
removes the DC bias from an incoming signal. The AC-
coupling capacitor allows the amplifier to bias the signal
to an optimum DC level. Assuming zero-source imped-
ance, the -3dB point of the highpass filter is given by:
Choose CIN so that f-3dB is well below the lowest fre-
quency of interest. Setting f-3dB too high affects the
low-frequency response of the amplifier. Use capaci-
tors with dielectrics that have low-voltage coefficients,
such as tantalum or aluminum electrolytic. Capacitors
with high-voltage coefficients, such as ceramics, may
result in increased distortion at low frequencies.
Output Filter
The MAX9708 does not require an output filter.
However, output filtering can be used if a design is fail-
ing radiated emissions due to board layout or cable
length, or the circuit is near EMI-sensitive devices.
Refer to the MAX9708 Evaluation Kit for suggested filter
topologies. The tuning and component selection of the
filter should be optimized for the load. A purely resistor
load (8
Ω) used for lab testing will require different com-
ponents than a real, complex load-speaker load.
Charge-Pump Capacitor Selection
The MAX9708 has an internal charge-pump converter
that produces a voltage level for internal circuitry. It
requires a flying capacitor (C1) and a holding capacitor
(C2). Use capacitors with an ESR less than 100m
Ω for
optimum performance. Low-ESR ceramic capacitors
minimize the output resistance of the charge pump. For
best performance over the extended temperature
range, select capacitors with an X7R dielectric. The
capacitors’ voltage rating must be greater than 36V.
f
RC
dB
IN
=
3
1
2
π
Figure 4. Single-Ended Input Connections
INR+
INR-
MAX9708
1
μF
1
μF
相關PDF資料 |
PDF描述 |
|---|---|
| VJ1210Y101MXPAT5Z | CAP CER 100PF 250V 20% X7R 1210 |
| MS27473T10B98SA | CONN PLUG 6POS STRAIGHT W/SCKT |
| VE-21Y-IU-F2 | CONVERTER MOD DC/DC 3.3V 132W |
| VE-B5X-IV-F4 | CONVERTER MOD DC/DC 5.2V 150W |
| VJ1210Y101KXLAT5Z | CAP CER 100PF 630V 10% X7R 1210 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9708ETN-T | 制造商:Maxim Integrated Products 功能描述:20W/40W FILTERLESS, SPREAD-SPECTRUM, MONO/STE - Tape and Reel |
| MAX9708EVKIT | 功能描述:音頻放大器 Evaluation Kit for the MAX9708 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9709ECB+ | 制造商:Maxim Integrated Products 功能描述:AUD AMP SPKR 1CH MONO/2CH STEREO 50W/29W CLS-D 64TQFP EP - Rail/Tube |
| MAX9709ECB+T | 制造商:Maxim Integrated Products 功能描述:AUD AMP SPKR 1CH MONO/2CH STEREO 50W/29W CLS-D 64TQFP EP - Tape and Reel |
| MAX9709ETN | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。