- 您現在的位置：買賣IC網 > PDF目錄10667 > MAX9647AUK+T (Maxim Integrated Products)IC COMPARATOR GP SGL SOT23-5 PDF資料下載
參數資料
| 型號： | MAX9647AUK+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMPARATOR GP SGL SOT23-5 |
| 標準包裝： | 2,500 |
| 類型： | 通用 |
| 元件數： | 1 |
| 輸出類型： | 開路漏極 |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 電壓 - 輸入偏移（最小值）： | 7mV @ 5V |
| 電流 - 輸入偏壓（最小值）： | 0.25µA @ 5V |
| 電流 - 輸出（標準）： | 35mA @ 5V |
| 電流 - 靜態（最大值）： | 120µA |
| CMRR, PSRR（標準）： | 90dB PSRR |
| 傳輸延遲（最大）： | 110ns |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | * |
| 安裝類型： | * |
| 包裝： | * |
MAX9647/MAX9648
General-Purpose, Low-Voltage,
Tiny Pack Comparators
9
Maxim Integrated
Additional hysteresis can be generated with two resis-
tors using positive feedback (Figure 2). Use the following
procedure to calculate resistor values:
1) Find output voltage when output is high:
VOUT(HIGH) = VDD - ILOAD x RL
2) Find the trip points of the comparator using these
formulas:
VTH = VREF + ((VOUT(HIGH) - VREF)R2)/(R1 + R2)
VTL = VREF(1 - (R2/(R1 + R2)))
where VTH is the threshold voltage at which the compara-
tor switches its output from high to low as VIN rises above
the trip point, and VTL is the threshold voltage at which
the comparator switches its output from low to high as
VIN drops below the trip point.
3) The hysteresis band is:
VHYST = VTH - VTL = VDD(R2/(R1 + R2))
In this example, let VDD = 5V, VREF = 2.5V, ILOAD =
50nA, and RL = 5.1kI.
VOUT(HIGH) = 5.0V - (50 x 10-9 x 5.1 x 103I) ≈ 5.0V
VTH = 2.5 + 2.5(R2/(R1 + R2))
VTL = 2.5(1 - (R2/(R1 + R2)))
Select R2. In this example, choose 1kI.
Select VHYST. In this example, choose 50mV.
Solve for R1.
VHYST = VOUT(HIGH)(R2/(R1 + R2))V
0.050V = 5(1000/(R1 + 1000))V
where R1
≈ 100kI, VTH = 2.525V, and VTL = 2.475V
Choose R1 and R2 to be large enough as not to exceed
the amount of current the reference can supply.
The source current required is VREF/(R1 + R2).
The sink current is (VOUT(HIGH) - VREF) x (R1 + R2).
Choose RL to be large enough to avoid drawing excess
current, yet small enough to supply the necessary cur-
rent to drive the load. RL should be between 1kI and
10kI. Choose R1 to be much larger than RL to avoid
lowering VOUT(HIGH) ir raising VOUT(LOW).
Board Layout and Bypassing
Use 0.1FF bypass capacitors from VDD to VSS. To maxi-
mize performance, minimize stray inductance by putting
this capacitor close to the VDD pin and reducing trace
lengths. For slow moving input signals (rise time > 1ms),
use a 1nF capacitor between IN+ and IN- to reduce high
frequency noise.
Figure 1. Threshold Hysteresis Band (Not to Scale)
Figure 2. Adding Hysteresis with External Resistors
IN+
THRESHOLDS
IN-
VHYST
VTL
VTH
HYSTERESIS
BAND
OUT
IN+
OUT
RL
R1
R2
VREF
VIN
VDD
VOUT
VDD
VSS
IN-
MAX9647
相關PDF資料 |
PDF描述 |
|---|---|
| AD7687BRMZ | IC ADC 16BIT 250KSPS 10-MSOP |
| CS5509-ASZ | IC ADC 16BIT SGNL SUPP 16-SOIC |
| HA1-4900-2 | IC COMPARATOR QUAD PREC 16-DIP |
| LTC1867ACGN#PBF | IC ADC 16BIT 8CH 200KSPS 16SSOP |
| MC10E1652FNG | IC COMPARATOR DUAL ECL 20PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9647AXK+ | 制造商:Maxim Integrated Products 功能描述:GENERAL-PURPOSE LOW-VOLTAGE SINGLE/DUAL/QUAD TINYPACK COMPAR - Rail/Tube |
| MAX9647AXK+T | 功能描述:校驗器 IC Low-Power Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9647EVKIT# | 功能描述:其他開發工具 MAX9647 Eval Kit RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓: |
| MAX9648AUK+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX9648AUK+T | 功能描述:校驗器 IC Low-Power Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。