- 您現在的位置：買賣IC網 > PDF目錄11699 > MAX9273GTL+ (Maxim Integrated Products)IC GMSL SERIALIZER PDF資料下載
參數資料
| 型號： | MAX9273GTL+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 27/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC GMSL SERIALIZER |
| 標準包裝： | 50 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
MAX9273
22-Bit GMSL Serializer with Coax or
STP Cable Drive
33
Maxim Integrated
Table 8. Modulation Coefficients and
Maximum SDIV Settings
Additional Error Detection and Correction
In default mode (additional error detection and correction
disabled), data encoding/decoding is the same as in pre-
vious GMSL serializers/deserializers (parity only). At the
serializer, the parallel input word is scrambled and a par-
ity bit added. The scrambled word is divided into 3 or 4
bytes (depending on the BWS setting), 8b/10b encoded,
and then transmitted serially. At the deserializer, the same
operations are performed in reverse order. The parity bit
is used by the deserializer to find the word boundary and
for error detection. Errors are counted in an error counter
register and an error pin indicates errors.
The serializer can use of of two additional error-detection/
correction methods (selectable by register setting):
1) 6-bit cyclic redundancy check
2) 6-bit hamming code with 16-word interleaving
Cyclic Redundancy Check (CRC)
When CRC is enabled, the serializer adds 6 bits of CRC to
the input data. This reduces the available bits in the input
data word by 6, compared to the non-CRC case (see
Table 2 for details). For example, 16 bits are available for
input data instead of 22 bits when BWS = 0, and 24 bits
instead of 30 bits when BWS = 1.
The CRC generator polynomial is x6 + x + 1 (as used in
the ITU-T G704 telecommunication standard).
The parity bit is still added when CRC is enabled,
because it is used for word-boundary detection. When
CRC is enabled, each data word is scrambled and then
the 6-bit CRC and 1-bit parity are added before the
8b/10b encoding.
At the deserializer, the CRC code is recalculated. If the
recalculated CRC code does not match the received CRC
code, an error is flagged. This CRC error is reported to the
error counter.
Hamming Code
Hamming code is a simple and effective error-correction
code to detect and/or correct errors. The MAX9273 seri-
alizer (when used with the MAX9272 GMSL deserializer)
uses single-error correction/double-error detection per
pixel hamming-code scheme.
The serializer uses data interleaving for burst-error toler-
ance. Burst errors up to 11 consecutive bits on the serial
link are corrected, and burst errors up to 31 consecutive
bits are detected.
Hamming code adds overhead similar to CRC. See Table 2
for details regarding the available input word size.
HS/VS Encoding and/or Tracking
HS/VS encoding by a GMSL serializer allows horizontal
and vertical synchronization signals to be transmitted
while conserving pixel data bandwidth. With HS/VS
encoding enabled, 10-bit pixel data with a clock up to
100MHz can be transmitted using 1 pixel of data per HS/
VS transition, versus 8-bit data with a clock up to 100MHz
without HS/VS encoding. The deserializer performs HV
decoding, tracks the period of the HV signals, and uses
voting to filter HS/VS bit errors. When using HV encod-
ing, use a minimum low-pulse duration of two PCLKIN
cycles when DBL = 0 on the MAX9271/MAX9273. When
DBL = 1, use a minimum HS/VS low-pulse duration of
five PCLKIN cycles and a minimum high-pulse duration
of two PCLKIN cycles. When using hamming code and
HS/VS encoding, do not send more than two transitions
every 16 PCLKIN cycles.
When the serializer uses double-input mode (DBL = 1),
the active duration, plus the blanking duration of HS or
VS signals, should be an even number of PCLKIN cycles.
If HS/VS tracking is used without HV encoding, use DIN0
for HSYNC and DIN1 for VSYNC. In this case, if DBL
values on the serializer and the deserializer are different,
set the deserializer’s UNEQDBL register bit to 1. If the
BWS
SPREAD-
SPECTRUM
SETTING (%)
MODULATION
COEFFICIENT
(dec)
SDIV UPPER
LIMIT (dec)
1
104
40
0.5
104
63
3
152
27
1.5
152
54
4
204
15
2
204
30
0
1
80
52
0.5
80
63
3
112
37
1.5
112
63
4
152
21
2
152
42
相關PDF資料 |
PDF描述 |
|---|---|
| R5F100CCALA#U0 | MCU 16BIT 32KB FLASH 36FLGA |
| R5F101JCAFA#V0 | MCU 16BIT 32KB FLASH 52LQFP |
| R5F100BDANA#U0 | MCU 16BIT 48KB FLASH 32WQFN |
| R5F1008DALA#U0 | MCU 16BIT 48KB FLASH 25FLGA |
| C8051F574-IM | IC 8051 MCU 16K FLASH 40-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9273GTL/V+ | 功能描述:串行器/解串器 - Serdes 1.5Gbps 22-bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9273GTL/V+T | 功能描述:串行器/解串器 - Serdes 1.5Gbps 22-bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9273GTL+ | 功能描述:串行器/解串器 - Serdes 1.5Gbps 22-bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9273GTL+T | 功能描述:串行器/解串器 - Serdes 1.5Gbps 22Bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9275GTN/V+T | 制造商:Maxim Integrated Products 功能描述:SERIALIZER WITH PARALLEL CMOS INPUTS, NON-HDCP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。