- 您現在的位置：買賣IC網 > PDF目錄385552 > MAX848-MAX849 (Maxim Integrated Products, Inc.) 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters PDF資料下載
參數資料
| 型號： | MAX848-MAX849 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | DC/DC變換器 |
| 英文描述： | 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters |
| 中文描述： | 1節至3節電池，大功率，低噪聲，升壓型DC - DC轉換器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 166K |
| 代理商： | MAX848-MAX849 |
M
1-Cell to 3-Cell, High-Power,
Low-Noise, S tep-Up DC-DC Converters
12
______________________________________________________________________________________
When using two counters of the same length, as shown
in Figure 8, one counter (A) just counts the A/D clock
pulses (f
OSC
/2), and the other counter (B) counts DATA
output pulses. When counter A overflows (for example,
after 256 clock cycles for an 8-bit counter), counter B is
disabled. The controller reads the counter B output
data and calculates the analog voltage present at the
ADC’s input.
All μC Implementation
This implementation uses a μC timer and a counter.
The timer and the counter are reset at the same time.
The counter counts data-output pulses applied at its
input. When the timer times out, an interrupt is assert-
ed. The μC then reads the state of the counter register.
The interrupt-handling overhead can cause the counter
to count more pulses than desired. Accuracy depends
on how long the μC needs to read the counter. No
errors will occur if the counter is disabled within one
clock period. Interrupt latency reduces accuracy. The
main advantage of this implementation is that no exter-
nal hardware is required.
__________________Design Proc edure
Induc tor S elec tion
The MAX848/MAX849’s high switching frequency allows
the use of a small inductor. Use a 10μH inductor for the
MAX849 and a 22μH inductor for the MAX848. Inductors
with a ferrite core or equivalent are recommended; pow-
der iron cores are not recommended for use with high
switching frequencies. Make sure the inductor’s satura-
tion rating (the current at which the core begins to satu-
rate and inductance starts to fall) exceeds the internal
current limit: 0.8A for the MAX848 and 1.4A for the
MAX849. However, it is generally acceptable to bias the
inductor into saturation by approximately 20% (the point
where the inductance is 20% below the nominal value).
For highest efficiency, use a coil with low DC resistance,
preferably under 100m
. To minimize radiated noise,
use a toroid, pot core, or shielded inductor. See Table 5
for a list of suggested inductor suppliers.
Diode S elec tion
The MAX848/MAX849’s high switching frequency
demands a high-speed rectifier. Schottky diodes, such
as the 1N5817 or MBR0520L, are recommended. Make
sure the diode’s current rating exceeds the maximum
load current and that its breakdown voltage exceeds
V
OUT
.
The Schottky rectifier diode carries load currents only in
the PFM operating mode, since the P-channel synchro-
nous rectifier is disabled. Therefore, the current rating
need not be high (0.5A is sufficient). In PFM mode, the
voltage drop across the rectifier diode causes efficien-
cy loss. However, when operating in PWM mode, the
internal P-channel synchronous rectifier is active and
efficiency loss due to the rectifier diode is minimized.
For high-temperature applications, Schottky diodes
may be inadequate due to their high leakage currents;
use high-speed silicon diodes such as the MUR105 or
EC11FS1. At heavy loads and high temperatures, the
benefits of a Schottky diode’s low forward voltage may
outweigh the disadvantage of high leakage current.
See Table 4 for a list of suggested diode suppliers.
f
OSC
/2
DATA
GIVES YOU 2-BIT RESOLUTION
COUNTING FOUR PULSES
Figure 7. Bit Stream at 1/2 Full Scale
EN
CLR
CLK
RC
8-BIT COUNTER
CLR
CLK
EN
8-BIT COUNTER
LATCH
÷
2
V
CC
CLOCK/SEL
OR LX
CLEAR
CARRY OUTPUT
DATA OUTPUT
A
B
Figure 8. Discrete Hardware Solution for Counting A/D Output
Data Pulses
相關PDF資料 |
PDF描述 |
|---|---|
| MAX849ESE | 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters |
| MAX848ESE | 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters |
| MAX848 | Low-Noise, Step-Up DC-DC Converters(高功率，低噪，帶0.5AMOSFET功率開關,步升DC-DC變換器) |
| MAX849 | Low-Noise, Step-Up DC-DC Converters(高功率，低噪，帶0.5AMOSFET功率開關,步升DC-DC變換器) |
| MAX8530 | Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX849ESE | 功能描述:直流/直流開關轉換器 1-3 Cell Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX849ESE+ | 功能描述:直流/直流開關轉換器 1-3 Cell Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX849ESE+T | 功能描述:直流/直流開關轉換器 1-3 Cell Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX849ESE-T | 功能描述:直流/直流開關轉換器 1-3 Cell Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX849EVKIT | 功能描述:直流/直流開關轉換器 1-Cell to 3-Cell High-Power Low-Noise Step-Up DC-DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。