- 您現在的位置：買賣IC網 > PDF目錄385552 > MAX847 (Maxim Integrated Products, Inc.) Quadruple 2-Line To 1-Line Data Selectors/Multiplexers 16-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX847 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Quadruple 2-Line To 1-Line Data Selectors/Multiplexers 16-CDIP -55 to 125 |
| 中文描述： | 1節電池、升壓型、雙向?qū)ず魴C(jī)系統電源IC |
| 文件頁數： | 13/18頁 |
| 文件大?。?/td> | 167K |
| 代理商： | MAX847 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁
Bac kup Linear Regulator
The BACKUP serial input bit turns on the backup regu-
lator, which sources current from NICD to OUT. This
regulator backs up OUT by using the rechargeable bat-
tery (at NICD) when the main battery (at BATT) is
depleted or removed. The backup regulator pass
device’s resistance is typically 5
, so it can typically
supply 20mA with only 100mV of dropout.
All DC-DC converter and charging circuitry is disabled
when the backup regulator is turned on, but all other
functions remain active. Activate BACKUP manually by
serial command, or set it to trigger automatically when
LBO goes low.
Automatic Bac kup
Setting the LBO_Sets_BACKUP serial bit (Table 2) pro-
grams the IC so that when LBO goes low, the backup
regulator automatically turns on without instructions
from the microprocessor (μP). When the LBO_
Sets_BACKUP bit is 0, the backup regulator is turned
on only by setting the BACKUP bit. The BACKUP bit
also overrides the LBO_Sets_BACKUP bit. Figure 4
shows the logic for this function.
If the main battery is depleted, and the NICD battery is
drained during backup, RSO goes low while the back-
up regulator is supplying OUT (if RSI is used to monitor
OUT or REG1). When RSO falls, the serial registers
reset to their POR states (with the DC-DC converter on
in Coast Mode and the backup regulator off, Tables 2,
3, and 4). This prevents the IC from getting hung up
with the DC-DC converter off when a new main battery
is inserted. This sequence is required because if the
MAX847 did not default to “DC-DC converter on” when
coming out of reset, the μP (still reset by RSO) would
not be able to provide the device with serial instructions
to turn on.
S erial Interfac e
The MAX847 has an SPI-compatible serial interface.
The serial-interface lines are Chip Select (
CS
), Serial
Clock (SCL), Serial Data In (SDI), and Serial Data Out
(SDO). Serial input data is arranged in 8-bit bytes. Most
bytes contain a 3-bit address pointer (R2, R1, R0)
along with 5 bits of input data (D4–D0). For common
operations such as selecting Run or Coast Mode, acti-
vating REG2 or REG3, or turning on DR1 or DR2, only
the 000 (R2, R1, R0) address register needs to be writ-
ten. The serial input data format for all MAX847 opera-
tions is outlined in Tables 2, 3, and 4.
M
1-Cell, S tep-Up
Two-Way Pager S ystem IC
______________________________________________________________________________________
13
15mA_CHG
1mA_CHG
TO
CHARGER
CONTROL
TO
BACKUP
REGULATOR
BACKUP
LBO_SETS_BACKUP
LBO
Figure 4. Logic for Charger Control and BACKUP, and for
LBO_Sets_BACKUP Serial Input Bits
INPUT BIT
LBO_Sets_BACKUP
1 = Allow LBO to turn on backup regulator and disable DC-DC converter (POR state is no con-
nection between LBO and BACKUP).
OV0–OV4
RUN/COAST
REG2_ON, REG3_ON
DR1, DR2
Sets OUT Output Voltage (POR state is V
OUT
= 3.0V).
Sets 7-bit CH DAC voltage for A/D conversion (POR state is all zeros with DAC and compara-
tors off).
DAC0–DAC6
1mA_CHG, 15mA_CHG
FUNCTION
1 = Run Mode, 0 = Coast Mode (POR state is Coast Mode).
1 = Turn on selected regulator (POR state is off).
1 = Turn on selected switch (POR state is off).
1 = Turn on selected charge current to NICD. If both are set, the charge current is 15mA (POR
state is off).
BACKUP
1 = Turn on backup linear regulator from NICD to OUT and disable DC-DC converter (POR
state is BACKUP off). Setting this bit overrides 1mA_CHG, 15mA_CHG, and LBO_Sets_BACK-
UP (Figure 1).
Table 4. Input-Bit Function Description
相關PDF資料 |
PDF描述 |
|---|---|
| MAX848-MAX849 | 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters |
| MAX849ESE | 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters |
| MAX848ESE | 1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters |
| MAX848 | Low-Noise, Step-Up DC-DC Converters(高功率，低噪，帶0.5AMOSFET功率開關,步升DC-DC變換器) |
| MAX849 | Low-Noise, Step-Up DC-DC Converters(高功率，低噪，帶0.5AMOSFET功率開關,步升DC-DC變換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX847EEI | 功能描述:電池管理 1 Cell Step-Up 2-Way Pager System IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX847EEI+ | 功能描述:電池管理 1 Cell Step-Up 2-Way Pager System IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX847EEI+T | 功能描述:電池管理 1 Cell Step-Up 2-Way Pager System IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX847EEI-C70955 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX847EEI-T | 功能描述:電池管理 1 Cell Step-Up 2-Way Pager System IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。