- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX786CAI (Maxim Integrated)IC REG QD BCK/LINEAR SYNC 28SSOP Datasheet資料下載
參數資料
| 型號： | MAX786CAI |
| 廠商： | Maxim Integrated |
| 文件頁數： | 15/20頁 |
| 文件大?。?/td> | 305K |
| 描述： | IC REG QD BCK/LINEAR SYNC 28SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 拓撲： | 降壓（降壓）同步（2），線性（LDO）（2） |
| 功能： | 任何功能 |
| 輸出數： | 4 |
| 頻率 - 開關： | 300kHz，200kHz |
| 電壓/電流 - 輸出 1： | 控制器 |
| 電壓/電流 - 輸出 2： | 控制器 |
| 電壓/電流 - 輸出 3： | 5V，5mA |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 5.5 V ~ 30 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
| 其它名稱： | 146982F |
Dual-Output Power-Supply
Controller for Notebook Computers
______________________________________________________________________________________ 15
Be sure to select output capacitors that satisfy both
the minimum capacitance and maximum ESR require-
ments. To achieve the low ESR required, it may be
appropriate to use a capacitance value 2 or 3 times
larger than the calculated minimum.
The output ripple in continuous-current mode is:
V
OUT(RPL)
= I
LPP(MAX)
x (ESR
CF
+ 1/(2 x 纗 f x C
F
) ).
In idle-mode, the ripple has a capacitive and resistive
component:
(4) (10
-4
) (L)
V
OUT(RPL)
(C) = x
(R
CS
2
) (C
F
)
1 1
(
+
)
Volts
V
OUT
V
IN
- V
OUT
(0.02) (ESR
CF
)
V
OUT(RPL)
(R) = - Volts
R
CS
The total ripple, V
OUT(RPL)
, can be approximated as
follows:
if V
OUT(RPL)
(R) < 0.5 V
OUT(RPL)
(C),
then V
OUT(RPL)
= V
OUT(RPL)
(C),
otherwise, V
OUT(RPL)
= 0.5 V
OUT(RPL)
(C) +
V
OUT(RPL)
(R).
Diodes D1 and D3
Use 1N5819s or similar Schottky diodes. D1 and D3
conduct only about 3% of the time, so the 1N5819s
1A current rating is conservative. The voltage rating
of D1 and D3 must exceed the maximum input supply
voltage from the battery. These diodes must
be Schottky diodes to prevent the lossy MOSFET
body diodes from turning on, and they must be
placed physically close to their associated synchro-
nous rectifier MOSFETs.
Soft-Start Capacitors (C8, C9)
A capacitor connected from GND to either SS pin
causes that supply to ramp up slowly. The ramp time to
full current limit, t
SS
, is approximately 1ms for every nF
of capacitance on SS_, with a minimum value of 10祍.
Typical capacitor values are in the 10nF to 100nF
range; a 5V rating is sufficient.
Because this ramp is applied to the current-limit circuit,
the actual time for the output voltage to ramp up
depends on the load current and output capacitor
value. Using Figure 1s circuit with a 2A load and no SS
capacitor, full output voltage is reached about 600祍
after ON_ is driven high.
Boost Capacitors (C4, C5)
Capacitors C4 and C5 store the boost voltage and pro-
vide the supply for the DH3 and DH5 drivers. Use 0.1礔
and place each within 10mm of the BST_ and LX_ pins.
Boost Diodes (D1A, D1B)
Use high-speed signal diodes; e.g., 1N4148 or
equivalent.
Bypass Capacitors
Input Filter Capacitors (C1, C10)
Use at least 3礔/W of output power for the input filter
capacitors, C1 and C10. They should have less than
150m& ESR, and should be located no further than
10mm from N1 and N2 to prevent ringing. Connect the
negative terminals directly to PGND. Do not exceed the
surge current ratings of input bypass capacitors.
Shutdown Mode
Shutdown (SHDN
= low) forces both PWMs off and dis-
ables the REF output and both comparators (Q1 = Q2
= 0V). Supply current in shutdown mode is typically
25礎. The VL supply remains active and can source
25mA for external loads. Note that the VL load capabili-
ty is higher in shutdown and standby modes than when
the PWMs are operating (25mA vs. 5mA). Standby
mode is achieved by holding ON3 and ON5 low while
SHDN
is high. This disables both PWMs, but keeps VL,
REF, and the precision comparators alive. Supply current
in standby mode is typically 70礎.
MAX786
KELVIN SENSE TRACES
SENSE RESISTOR
MAIN CURRENT PATH
FAT, HIGH-CURRENT TRACES
Figure 5. Kelvin Connections for the Current-Sense Resistors
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8533EUB+T | IC HOT-SWAP CNTRLR 12V 10-UMAX |
| MAX8563EEE+ | IC REG CTRLR TRPL POS ADJ 16QSOP |
| MAX8667ETEAA+ | IC REG QD BCK/LINEAR SYNC 16TQFN |
| MAX8836ZEREEE+T | IC REG DL BCK/LINEAR SYNC 16UCSP |
| MAX8884YEREKE+T | IC REG TRPL BCK/LINEAR 16UCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX786CAI+ | 功能描述:DC/DC 開關控制器 Dual-Output Power Supply Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX786CAI+T | 功能描述:DC/DC 開關控制器 Dual-Output Power Supply Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX786CAI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX786EAI | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX786EAI+ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。