- 您現在的位置：買賣IC網 > PDF目錄11709 > MAX7347AEE+ (Maxim Integrated Products)IC CNTRL SW SOUND 16-QSOP PDF資料下載
參數資料
| 型號： | MAX7347AEE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CNTRL SW SOUND 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 應用： | 聲卡，播放器，記錄器 |
| 接口： | I²C |
| 電源電壓： | 2.4 V ~ 3.6 V |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MAX7347/MAX7348/MAX7349
2-Wire Interfaced Low-EMI Key Switch
and Sounder Controllers
10
______________________________________________________________________________________
Bus Timeout
The MAX7347/MAX7348/MAX7349 feature a 20ms mini-
mum bus timeout on the 2-wire serial interface, largely to
prevent the MAX7347/MAX7348/MAX7349 from holding
the SDA I/O low during a read transaction if the SCL
hangs for any reason before a serial transaction has
been completed. Bus timeout operates by causing the
MAX7347/MAX7348/MAX7349 to internally terminate a
serial transaction, either read or write, if the time between
adjacent edges on SCL exceeds 20ms. After a bus time-
out, the MAX7347/MAX7348/MAX7349 wait for a valid
START condition before responding to a consecutive
transmission. The bus timeout feature requires the serial
interface to operate above 50Hz bus speed. This feature
can be enabled or disabled under user control by writing
to the configuration register (Table 12).
Message Format for Writing the
Key-Scan Controller
A write to the MAX7347/MAX7348/MAX7349s’ key-scan
controller
comprises
the
transmission
of
the
MAX7347/MAX7348/MAX7349s’ key-scan slave address
with the R/W bit set to zero, followed by at least 1 byte of
information. The first byte of information is the command
byte. The command byte determines which register of the
MAX7347/MAX7348/MAX7349 is to be written by the next
byte, if received. If a STOP condition is detected after the
command byte is received, then the MAX7347/MAX7348
/MAX7349 take no further action (Figure 7) beyond stor-
ing the command byte.
Any bytes received after the command byte are data
bytes. The first data byte goes into the internal register
of the MAX7347/MAX7348/MAX7349 selected by the
command byte (Figure 8).
If multiple data bytes are transmitted before a STOP
condition is detected, these bytes are generally stored
in subsequent MAX7347/MAX7348/MAX7349 internal
registers (Table 7) because the command byte address
generally autoincrements (Table 4).
Message Format for Reading the
Key-Scan Controller
The MAX7347/MAX7348/MAX7349 are read using the
MAX7347/MAX7348/MAX7349s’ internally stored com-
mand byte as an address pointer, the same way the
stored command byte is used as an address pointer for
a write. The pointer generally autoincrements after each
data byte is read using the same rules as for a write
(Table 4). Thus, a read is initiated by first configuring
the MAX7347/MAX7348/MAX7349s’ command byte by
performing a write (Figure 7). The master can now read
n consecutive bytes from the MAX7347/MAX7348/
MAX7349, with the first data byte being read from the
register addressed by the initialized command byte.
When performing read-after-write verification, remem-
ber to reset the command byte’s address because the
stored command byte address is generally autoincre-
mented after the write (Figure 9, Table 4).
SDA
SCL
01
1
A3
A2
A1
1
MSB
LSB
ACK
R/W
Figure 6. Slave Address
SCL
SDA
BY
TRANSMITTER
CLOCK PULSE FOR
ACKNOWLEDGE
START
CONDITION
SDA
BY
RECEIVER
1
2
8
9
S
Figure 5. Acknowledge
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26FJ61PB | CONN PLUG 61POS STRAIGHT W/PINS |
| D38999/26WB5PB | CONN PLUG 5POS STRAIGHT W/PINS |
| D38999/20MB5PN | CONN RCPT 5POS WALL MNT W/PINS |
| MS27467E25F29P | CONN PLUG 29POS STRAIGHT W/PINS |
| D38999/26WJ61PC | CONN PLUG 61POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7347AEE+ | 功能描述:外圍驅動器與原件 - PCI Low-EMI Key Switch & Sounder Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| MAX7347AEE+T | 功能描述:外圍驅動器與原件 - PCI Low-EMI Key Switch & Sounder Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| MAX7347AEE-T | 功能描述:外圍驅動器與原件 - PCI Low-EMI Key Switch & Sounder Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| MAX7347ATE+ | 功能描述:外圍驅動器與原件 - PCI Low-EMI Key Switch & Sounder Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| MAX7347ATE+T | 功能描述:外圍驅動器與原件 - PCI Low-EMI Key Switch & Sounder Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。