- 您現在的位置：買賣IC網 > PDF目錄3767 > MAX7325ATG+T (Maxim Integrated Products)IC I/O EXPANDER I2C 8B 24TQFN-EP PDF資料下載
參數資料
| 型號： | MAX7325ATG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 24TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接口： | I²C |
| 輸入/輸出數： | 8 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 1.71 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-TQFN-EP（4x4） |
| 包裝： | 帶卷 (TR) |
| 包括： | POR |
MAX7325
I2C Port Expander with 8 Push-Pull
and 8 Open-Drain I/Os
7
Maxim Integrated
The open-drain ports offer latching transition detection
when used as inputs. All input ports are continuously
monitored for changes. An input change sets one of 8
flag bits that identify changed input(s). All flags are
cleared upon a subsequent read or write transaction to
the MAX7325.
A latching interrupt output, INT, is programmed to flag
logic changes on ports used as inputs. Data changes
on any input port forces INT to a logic-low. Changing
the I/O port level through the serial interface does not
cause an interrupt. The interrupt output INT is deassert-
ed when the MAX7325 is next accessed through the
serial interface.
Internal pullup resistors to V+ are selected by the
address select inputs, AD0 and AD2. Pullups are
enabled on the input ports in groups of four (see Table 2).
Use the slave address selection to ensure that I/O ports
used as inputs are logic-high on power-up. I/O ports
with internal pullups enabled default to a logic-high out-
put state. I/O ports with internal pullups disabled
default to a logic-low output state.
Output port power-up logic levels are selected by the
address select inputs, AD0 and AD2. Ports default to
logic-high or logic-low on power-up in groups of four
(see Tables 2 and 3).
Initial Power-Up
On power-up, the transition detection logic is reset, and
INT is deasserted. The transition flags are cleared to indi-
cate no data changes. The power-up default states of the
16 I/O ports are set according to the I2C slave address
selection inputs, AD0 and AD2 (Tables 2 and 3). For I/O
ports used as inputs, ensure that the default states are
logic-high so that the I/O ports power up in the high-
impedance state. All I/O ports configured with pullups
enabled also have a logic-high power-up state.
Power-On Reset
The MAX7325 contains an integral power-on-reset
(POR) circuit that ensures all registers are reset to a
known state on power-up. When V+ rises above VPOR
(1.6V max), the POR circuit releases the registers and
2-wire interface for normal operation. When V+ drops to
less than VPOR, the MAX7325 resets all register con-
tents to the POR defaults (Tables 2 and 3).
RST Input
The active-low RST input voids any I2C transaction
involving the MAX7325, forcing the MAX7325 into the
I2C STOP condition. A reset does not affect the inter-
rupt output (INT).
Standby Mode
When the serial interface is idle, the MAX7325 automatical-
ly enters standby mode, drawing minimal supply current.
Slave Address, Power-Up Default Logic
Levels, and Input Pullup Selection
Address inputs AD0 and AD2 determine the MAX7325
slave address, set the power-up I/O state for the ports,
and select which inputs have pullup resistors. Internal
pullups and power-up default states are set in groups
of four (see Table 2).
The MAX7325 slave address is determined on each I2C
transmission, regardless of whether the transmission is
actually addressing the MAX7325. The MAX7325 distin-
guishes whether address inputs AD0 and AD2 are con-
nected to SDA or SCL instead of fixed logic levels V+
or GND during this transmission. The MAX7325 slave
address can be configured dynamically in the applica-
tion without cycling the device supply.
On initial power-up, the MAX7325 cannot decode the
address inputs AD0 and AD2 fully until the first I2C
transmission. AD0 and AD2 initially appear to be
PART
I2C
SLAVE
ADDRESS
INPUTS
INPUT
INTERRUPT
MASK
OPEN-
DRAIN
OUTPUTS
PUSH-
PULL
OUTPUTS
CONFIGURATION
MAX7323
110xxxx
Up to 4
—
Up to 4
4
4 I/O, 4 output-only versions:
4 open-drain I/O ports with latching transition
detection interrupt and selectable pullups.
4 push-pull outputs with selectable power-up default
levels.
MAX7328
MAX7329
0100xxx
0111xxx
Up to 8
—
Up to 8
—
8 open-drain I/O ports with nonlatching transition
detection interrupt and pullups on all ports.
Table 1. MAX7319–MAX7329 Family Comparison (continued)
相關PDF資料 |
PDF描述 |
|---|---|
| IS82C55A96 | IC I/O EXPANDER 24B 44PLCC |
| IS82C55A | IC I/O EXPANDER 24B 44PLCC |
| IP82C55A | IC I/O EXPANDER 24B 40DIP |
| IS82C55A-5 | IC I/O EXPANDER 24B 44PLCC |
| ATMEGA168-20AUR | MCU AVR 16KB FLASH 20MHZ 32TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7325EVCMAXQU+ | 功能描述:界面開發工具 MAX7325 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX7325EVKIT+ | 功能描述:界面開發工具 MAX7325 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX7326 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C Port Expander with Eight Push-Pull Outputs and Eight Inputs |
| MAX7326AEG | 功能描述:接口-I/O擴展器 I2C Port Expander w/12 P-P Out & 4 In RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7326AEG+ | 功能描述:接口-I/O擴展器 I2C Port Expander w/12 P-P Out & 4 In RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。