- 您現在的位置：買賣IC網 > PDF目錄3767 > MAX7316AEE+ (Maxim Integrated Products)IC I/O EXPANDER I2C 16B 16QSOP PDF資料下載
參數資料
| 型號： | MAX7316AEE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 16QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 10 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 管件 |
MAX7316
Message Format for Reading
The MAX7316 is read using the MAX7316’s internally
stored command byte as an address pointer the same
way the stored command byte is used as an address
pointer for a write. The pointer autoincrements after
each data byte is read using the same rules as for a
write (Table 2). Thus, a read is initiated by first configur-
ing the MAX7316’s command byte by performing a
write (Figure 7). The master can now read n consecu-
tive bytes from the MAX7316 with the first data byte
being read from the register addressed by the initial-
ized command byte. When performing read-after-write
verification, remember to reset the command byte’s
address because the stored command byte address
has been autoincremented after the write (Table 2). A
diagram of a read from the input ports register is shown
in Figure 10 reflecting the states of the ports.
Operation with Multiple Masters
If the MAX7316 is operated on a 2-wire interface with
multiple masters, a master reading the MAX7316 should
use a repeated start between the write, which sets the
MAX7316’s address pointer, and the read(s) that takes
the data from the location(s) (Table 2). This is because it
is possible for master 2 to take over the bus after master
1 has set up the MAX7316’s address pointer but before
master 1 has read the data. If master 2 subsequently
changes the MAX7316’s address pointer, then master
1’s delayed read can be from an unexpected location.
Command Address Autoincrementing
The command address stored in the MAX7316 circu-
lates around grouped register functions after each data
byte is written or read (Table 2).
10-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
10
______________________________________________________________________________________
Figure 10. Read, Write, and Interrupt Timing Diagrams
SLAVE ADDRESS
1
23
4567
89
S A6 A5 A4 A3 A2 A1 A00
A
0
00
COMMAND BYTE
1A
A
P
START CONDITION
ACKNOWLEDGE FROM SLAVE
STOP
CONDITION
P7–P0
DATA1 VALID
DATA2 VALID
SLAVE ADDRESS
1
23
4567
89
S A6A5A4A3A2A1A0
1
A
COMMAND BYTE
ANA
START CONDITION
ACKNOWLEDGE FROM SLAVE
ACKNOWLEDGE FROM MASTER
P7–P0
STOP CONDITION
P
NO ACKNOWLEDGE FROM
MASTER
DATA2
DATA3
tDV
SLAVE ADDRESS
1
23
4567
89
S A6A5A4A3A2A1A0 1
A
COMMAND BYTE
ANA
START CONDITION
ACKNOWLEDGE FROM SLAVE
ACKNOWLEDGE FROM MASTER
P7–P0
STOP CONDITION
P
NO ACKNOWLEDGE FROM
MASTER
DATA1
DATA2
DATA3
DATA4
tDH
tDS
DATA1
tIV
tIR
tIV
SCL
SDA
SCL
SDA
SCL
SDA
WRITE TO OUTPUT PORTS REGISTERS (BLINK PHASE 0 REGISTERS/BLINK PHASE 1 REGISTERS)
READ FROM INPUT PORTS REGISTERS
INTERRUPT VALID/RESET
R/W
MSB
LSB
DATA1
MSB
LSB
DATA1
MSB
LSB
DATA2
MSB
LSB
DATA4
MSB
LSB
DATA4
MSB
LSB
DATA2
R/W
INT
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA8515L-8MUR | MCU AVR 8KB FLASH 8MHZ 44QFN |
| MAX7316ATE+ | IC I/O EXPANDER I2C 16B 16TQFN |
| ATMEGA8515-16MUR | MCU AVR 8KB FLASH 16MHZ 44QFN |
| MAX7315ATE+T | IC I/O EXPANDER I2C 8B 16TQFN-EP |
| MAX7315AUE+T | IC I/O EXPANDER I2C 8B 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7316AEE+ | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7316AEE+T | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7316AEE-T | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7316ATE | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7316ATE+ | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。