- 您現在的位置：買賣IC網 > PDF目錄3767 > MAX7315AUE+T (Maxim Integrated Products)IC I/O EXPANDER I2C 8B 16TSSOP PDF資料下載
參數資料
| 型號： | MAX7315AUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 8 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁
MAX7315
only as an input. A pullup resistor, typically 4.7k
, is
required on SCL if there are multiple masters on the 2-
wire interface, or if the master in a single-master system
has an open-drain SCL output.
Each transmission consists of a START condition
(Figure 3) sent by a master, followed by the MAX7315
7-bit slave address plus R/W bit, a register address
byte, one or more data bytes, and finally a STOP condi-
tion (Figure 3).
Start and Stop Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master
has finished communicating with the slave, it issues a
STOP (P) condition by transitioning SDA from low to
high while SCL is high. The bus is then free for another
transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on SDA must remain stable while SCL is high
(Figure 4).
Acknowledge
The acknowledge bit is a clocked 9th bit that the recipi-
ent uses to handshake receipt of each byte of data
(Figure 5). Thus, each byte transferred effectively
requires 9 bits. The master generates the 9th clock
pulse, and the recipient pulls down SDA during the
acknowledge clock pulse so the SDA line is stable low
during the high period of the clock pulse. When the
master is transmitting to the MAX7315, the device gen-
erates the acknowledge bit because the MAX7315 is
the recipient. When the MAX7315 is transmitting to the
master, the master generates the acknowledge bit
because the master is the recipient.
Slave Address
The MAX7315 has a 7-bit long slave address (Figure 6).
The eighth bit following the 7-bit slave address is the
R/W bit. The R/W bit is low for a write command, high
for a read command.
The slave address bits A6 through A0 are selected by
the address inputs AD0, AD1, and AD2. These pins can
be connected to GND, V+, SDA, or SCL. The MAX7315
has 64 possible slave addresses (Table 1) and, there-
fore, a maximum of 64 MAX7315 devices can be con-
trolled independently from the same interface.
Message Format for Writing the MAX7315
A write to the MAX7315 comprises the transmission of
the MAX7315’s slave address with the R/W bit set to
zero, followed by at least 1 byte of information. The first
byte of information is the command byte. The command
byte determines which register of the MAX7315 is to be
written to by the next byte, if received (Table 2). If a
STOP condition is detected after the command byte is
received, then the MAX7315 takes no further action
beyond storing the command byte.
8-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
8
_______________________________________________________________________________________
Figure 3. Start and Stop Conditions
SDA
SCL
START
CONDITION
STOP
CONDITION
S
P
Figure 4. Bit Transfer
SDA
SCL
DATA LINE STABLE;
DATA VALID
CHANGE OF DATA
ALLOWED
Figure 5. Acknowledge
SCL
SDA BY
TRANSMITTER
CLOCK PULSE
FOR ACKNOWLEDGE
START
CONDITION
SDA BY
RECEIVER
1
2
8
9
S
Figure 6. Slave Address
SDA
SCL
A5
MSB
LSB
ACK
A4
A1
A6
A3
A0
A2
R/W
相關PDF資料 |
PDF描述 |
|---|---|
| AT90USB162-16MUR | IC AVR MCU 16K FLASH 32QFN |
| MAX7321ATE+T | IC I/O EXPANDER I2C 8B 16TQFN-EP |
| MAX7320AEE+T | IC I/O EXPANDER I2C 8B 16QSOP |
| ATMEGA8U2-MUR | MCU AVR 8K FLASH 16MHZ 32VQFN |
| MAX7325ATG+T | IC I/O EXPANDER I2C 8B 24TQFN-EP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7315AUE-TG05 | 功能描述:接口-I/O擴展器 8-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7315EVCMAXQU+ | 功能描述:接口-I/O擴展器 8-Port I/O Expander with LED Intensity Control and Interrupt RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7315EVKIT+ | 功能描述:界面開發工具 Evaluation Kit for the MAX7315 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX7316 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Port I/O Expander with LED Intensity Control and Interrupt |
| MAX7316AEE | 功能描述:接口-I/O擴展器 10-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。