參數資料
型號: MAX6917EO50
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 時鐘/數據恢復及定時提取
英文描述: REAL TIME CLOCK, PDSO20
封裝: 0.150 INCH, 0.025 INCH PITCH, MO-137AD, QSOP-20
文件頁數: 18/31頁
文件大小: 349K
代理商: MAX6917EO50
MAX6917
I2C-Compatible RTC with Microprocessor
Supervisor, Alarm, and NV RAM Controller
______________________________________________________________________________________
25
Chip-Enable Output
When the CE transmission gate is enabled, the imped-
ance seen at CE_OUT is equivalent to a 46
(typ)
resistor in series with the source driving CE_IN. In the
disabled mode, the transmission gate is off and an
active pullup connects CE_OUT to VOUT (see Figures
14, 16). This pullup turns off when the transmission
gate is enabled.
Test Configuration Register
This is a read-only register.
Data Valid Bit
DATA VALID has a POR setting of zero, indicating that
the data in the MAX6917 RTC is not guaranteed to be
valid (Table 1). A read of the status register sets the
DATA VALID bit to one, indicating valid data in the
MAX6917 RTC. In a system that uses a backup power
supply, the DATA VALID bit should be set to one by the
system software on first system power-up by reading the
status register. After that, any time the system recovers
from a reset condition caused by VCC < VRST, the DATA
VALID bit can be read to see if the data stored during
operation from the backup power supply is still valid (i.e.,
the backup power supply did not drop out). A one indi-
cates valid data and a zero indicates corrupted data.
Any time the internal supply to the MAX6917 (either
VBATT or VCC depending upon the operating conditions)
drops below 1.5V to 1.6V (typ), the DATA VALID bit is set
to zero even if it has recently been set by a read of the
status register.
VCC
RESET
CE_OUT
CE_IN
2.0V
VRST
tRP
VBATT
VCC
tCED
tRCE
tRPD
VRST
Figure 16. Chip-Enable Timing Diagram
相關PDF資料
PDF描述
MAX6917EO30 REAL TIME CLOCK, PDSO20
MAX6917EO33 REAL TIME CLOCK, PDSO20
MAX8893AEWV+ SPECIALTY MICROPROCESSOR CIRCUIT, PBGA30
MAX8893BEWV+ SPECIALTY MICROPROCESSOR CIRCUIT, PBGA30
MAX8893CEWV+ SPECIALTY MICROPROCESSOR CIRCUIT, PBGA30
相關代理商/技術參數
參數描述
MAX6917EO50+ 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
MAX6917EO50+T 功能描述:實時時鐘 Integrated Circuits (ICs) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
MAX691AC/D 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX691ACPE 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX691ACPE+ 功能描述:監控電路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel