- 您現在的位置：買賣IC網 > PDF目錄67928 > MAX6862UK23+T (MAXIM INTEGRATED PRODUCTS INC) Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer PDF資料下載
參數資料
| 型號： | MAX6862UK23+T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | LEAD FREE, MO-178AA, SOT-23, 5 PIN |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 489K |
| 代理商： | MAX6862UK23+T |
MAX6854/MAX6855/MAX6856/MAX6858/MAX6860–MAX6869
Transient Immunity
In addition to issuing a reset to the P during power-up,
power-down, and brownout conditions, the MAX6854/
MAX6855/MAX6856/MAX6858/MAX6860–MAX6869 are
relatively immune to short-duration supply transients, or
glitches. The Maximum VCC Transient Duration vs. Reset
Threshold Overdrive graph in the Typical Operating
Characteristics shows this relationship.
The area below the curve of the graph is the region in
which these devices typically do not generate a reset
pulse. This graph was generated using a falling pulse
applied to VCC, starting 100mV above the actual reset
threshold, VTH, and ending below this threshold (reset-
threshold overdrive). As the magnitude of the transient
increases, the maximum allowable pulse width
decreases. Typically, a 100mV VCC transient duration
of 40s or less does not cause a reset.
Interfacing to Other Voltages for Logic
Compatibility
The open-drain RESET output can be used to interface
to a P with other logic levels. As shown in Figure 4, the
open-drain output can be connected to voltages from 0
to 5.5V.
Generally, the pullup resistor connected to RESET con-
nects to the supply voltage that is being monitored at
the IC’s VCC input. However, some systems use the
open-drain output to level-shift from the monitored sup-
ply to reset circuitry powered by another supply voltage.
Keep in mind that as the supervisor’s VCC decreases,
so does the IC’s ability to sink current at RESET.
Ensuring a Valid
RESET Down to VCC = 0V
(Push-Pull
RESET)
When VCC falls below 1.1V, RESET’s current-sinking
capability declines drastically. The high-impedance
CMOS logic inputs connected to RESET can drift to
undetermined voltages. This presents no problems in
most applications, since most Ps and other circuitry
do not operate with VCC below 1.1V.
In those applications where RESET must be valid down
to 0, add a pulldown resistor between RESET and GND
for the MAX6854/MAX6858/MAX6861/MAX6864/
MAX6867 push-pull outputs. The resistor sinks any stray
leakage currents, holding RESET low (Figure 5). Choose
a pulldown resistor that accommodates leakages, such
that RESET is not significantly loaded and is capable of
pulling to GND. The external pulldown cannot be used
with the open-drain reset outputs.
Watchdog Software Considerations
One way to help the watchdog timer monitor software
execution more closely is to set and reset the watchdog
Nanopower P Supervisory Circuits with
Manual Reset and Watchdog Timer
12
______________________________________________________________________________________
MAX6856
MAX6860
MAX6863
MAX6866
MAX6869
GND
N
RESET
1.8V
VCC
GND
3.3V
P
100k
Figure 4. Interfacing with Other Voltage Levels
VCC
2M
MAX6854
MAX6858
MAX6861
MAX6864
MAX6867
GND
RESET
Figure 5. Ensuring RESET Valid to VCC = Ground
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6862UK24+T | Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer |
| MAX6862UK25+T | Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer |
| MAX6862UK26+T | Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer |
| MAX6862UK27+T | Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer |
| MAX6862UK28+T | Nanopower µP Supervisory Circuits with Manual Reset and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6862UK24+T | 功能描述:監控電路 Single nPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6862UK24-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6862UK25+T | 功能描述:監控電路 Single nPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6862UK25-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6862UK26 | 制造商:Maxim Integrated Products 功能描述:NANOPOWER MICROPROCESSOR SUPERVISOR - Cut Tape Product 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。