- 您現在的位置：買賣IC網 > PDF目錄385546 > MAX6816EUS (Maxim Integrated Products, Inc.) PLASTIC ENCAPSULATED DEVICES PDF資料下載
參數資料
| 型號： | MAX6816EUS |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | PLASTIC ENCAPSULATED DEVICES |
| 中文描述： | 塑封器件 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 52K |
| 代理商： | MAX6816EUS |
V. Quality Assurance Information
A. Quality Assurance Contacts: Jim Pedicord (Reliability Lab Manager)
Bryan Preeshl (Executive Director)
Kenneth Huening (Vice President)
VI. Reliability Evaluation
A. Accelerated Life Test
The results of the 135
°
C biased (static) life test are shown in
Table 1
. Using these results, the Failure
Rate (
λ
) is calculated as follows:
λ
= 1 = 1.83 (Chi square value for MTTF upper limit)
MTTF
192 x 4389 x 80 x 2
Temperature Acceleration factor assuming an activation energy of 0.8eV
λ
= 13.57 x 10
-9
λ
= 13.57 F.I.T. (60% confidence level @ 25
°
C)
This low failure rate represents data collected from Maxim’s reliability monitor program. In addition to
routine production Burn-In, Maxim pulls a sample from every fabrication process three times per week and subjects
it to an extended Burn-In prior to shipment to ensure its reliability. The reliability control level for each lot to be
shipped as standard product is 59 F.I.T. at a 60% confidence level, which equates to 3 failures in an 80 piece
sample. Maxim performs failure analysis on any lot that exceeds this reliability control level. Maxim also performs
quarterly 1000 hour life test monitors. This data is published in the Product Reliability Report (
RR-1M
).
B. Moisture Resistance Tests
Maxim pulls pressure pot samples from every assembly process three times per week. Each lot sample
must meet an LTPD = 20 or less before shipment as standard product. Additionally, the industry standard
85
°
C/85%RH testing is done per generic device/package family once a quarter.
C. E.S.D. and Latch-Up Testing
The MS22 die type has been found to have all pins able to withstand a transient pulse of
±
2500V, per Mil-
Std-883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device
withstands a current of
±
250mA and/or
±
20V.
B. Outgoing Inspection Level: 0.1% for all electrical parameters guaranteed by the Datasheet.
0.1% For all Visual Defects.
C. Observed Outgoing Defect Rate: < 50 ppm
D. Sampling Plan: Mil-Std-105D
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6816 | 8-Bit Binary Counters With Input Registers 16-CDIP -55 to 125 |
| MAX6816EUS-T | 【15kV ESD-Protected, Single/Dual/Octal, CMOS Switch Debouncers |
| MAX6817 | 【15kV ESD-Protected, Single/Dual/Octal, CMOS Switch Debouncers |
| MAX6818 | 【15kV ESD-Protected, Single/Dual/Octal, CMOS Switch Debouncers |
| MAX6817EUT-T | 8-Bit Binary Counters With Input Registers 20-LCCC -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6816EUS+ | 制造商:Maxim Integrated Products 功能描述:CMOS SWIT DEBOUNCER 4PIN SOT-143 - Bulk 制造商:Maxim Integrated Products 功能描述:CMOS SWITCH DEBOUNCERS |
| MAX6816EUS+T | 功能描述:監控電路 Single Switch Debouncer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6816EUS+TG48 | 制造商:Maxim Integrated Products 功能描述:?15KV ESD-PROTECTED, SINGLE/DUAL/OCTAL, CMOS SWITCH DEBOUNCE - Tape and Reel |
| MAX6816EUS-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6817EUT | 制造商:Maxim Integrated Products 功能描述:MAXIM MAX6817EUT SWITCH DEBOUNCERS - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:Maxim MAX6817EUT Switch Debouncers |
發布緊急采購，3分鐘左右您將得到回復。