參數資料
型號： MAX6694TE9A+T
廠商： Maxim Integrated
文件頁數： 12/18頁
文件大?。?/td> 196K
描述： IC TEMP MONITOR 5CH 16TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
功能： 溫度監控系統（傳感器）
傳感器類型： 內部和外部
感應溫度： -40°C ~ 125°C，外部傳感器
精確度： ±3°C 本地（最大），±4°C 遠程（最大）
拓?fù)洌?/td> ADC，緩沖器，多路復用器，寄存器庫
輸出類型： SMBus?
輸出警報： 是
輸出風扇： 是
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-WQFN 裸露焊盤
供應商設備封裝： 16-TQFN-EP（5x5）
包裝： 帶卷 (TR)
5-Channel Precision Temperature Monitor
with Beta Compensation
12   ______________________________________________________________________________________
Configuration Byte Functions
There are three read-write configuration registers
(Tables 4, 5, and 6) that can be used to control the
MAX6694s operation.
Configuration 1 Register
The configuration 1 register (Table 4) has several func-
tions. Bit 7 (MSB) is used to put the MAX6694 either in
software standby mode (STOP) or continuous conver-
sion mode. Bit 6 resets all registers to their POR condi-
tions and then clears itself. Bit 5 disables the SMBus
timeout. Bit 3 enables resistance cancellation on chan-
nel 1. See the Series Resistance Cancellation section
for more details. Bit 2 enables beta compensation on
channel 1. See the Beta Compensation section for
more details. The remaining bits of the configuration 1
register are not used. The POR state of this register is
0000 1100 (0Ch).
Configuration 2 Register
The configuration 2 register functions are described in
Table 5. Bits 6, 3, 2, 1, and 0 are used to mask the
ALERT interrupt output. Bit 6 masks the local alert inter-
rupt and bits 3 through bit 0 mask the remote alert
interrupts. The power-up state of this register is 0000
0000 (00h).
Configuration 3 Register
Table 6 describes the configuration 3 register. Bits 3
and 0 mask the OVERT interrupt output for channels 4
and 1. The remaining bits, 7, 6, 5, 4, 2, and 1, are
reserved. The power-up state of this register is 0000
0000 (00h).
Status Register Functions
Status registers 1, 2, and 3 (Tables 7, 8, and 9) indicate
which (if any) temperature thresholds have been
exceeded and if there is an open-circuit or short-circuit
fault detected with the external sense junctions. Status
register 1 indicates if the measured temperature has
exceeded the threshold limit set in the ALERT registers
for the local or remote-sensing diodes. Status register 2
indicates if the measured temperature has exceeded
the threshold limit set in the OVERT registers. Status
register 3 indicates if there is a diode fault (open or
short) in any of the remote-sensing channels.
Bits in the alert status register clear by a successful
read, but set again after the next conversion unless the
fault is corrected, either by a drop in the measured tem-
perature or an increase in the threshold temperature.
The ALERT interrupt output follows the status flag bit.
Once the ALERT output is asserted, it can be
deasserted by either reading status register 1 or by
successfully responding to an alert response address.
In both cases, the alert is cleared even if the fault condi-
tion exists, but the ALERT output reasserts at the end of
the next conversion. The bits indicating the fault for the
OVERT interrupt output clear only on reading the status 2
register even if the fault conditions still exist. Reading the
status 2 register does not clear the OVERT interrupt out-
put. To eliminate the fault condition, either the measured
temperature must drop below the temperature threshold
minus the hysteresis value (4癈), or the trip temperature
must be set at least 4癈 above the current temperature.
Applications Information
Remote-Diode Selection
The MAX6694 directly measures the die temperature of
CPUs and other ICs that have on-chip temperature-
sensing diodes (see the Typical Application Circuit) or
it can measure the temperature of a discrete diode-
connected transistor.
Effect of Ideality Factor
The accuracy of the remote temperature measure-
ments depends on the ideality factor (n) of the remote
diode (actually a transistor). The MAX6694 is opti-
mized for n = 1.006 (channel 1) and n = 1.008 (chan-
nels 2, 3, and 4). A thermal diode on the substrate of an
IC is normally a pnp with the base and emitter brought
out to the collector (diode connection) grounded. DXP_
must be connected to the anode (emitter) and DXN_
must be connected to the cathode (base) of this pnp. If
a sense transistor with an ideality factor other than
1.006 or 1.008 is used, the output data is different from
the data obtained with the optimum ideality factor.
Fortunately, the difference is predictable. Assume a
remote-diode sensor designed for a nominal ideality
factor n
NOMINAL
is used to measure the temperature of
a diode with a different ideality factor n
1
. The measured
temperature T
M
can be corrected using:
where temperature is measured in Kelvin and
n
NOMIMAL
for channel 1 of the MAX6694 is 1.009. As
an example, assume you want to use the MAX6694 with
a CPU that has an ideality factor of 1.002. If the diode
has no series resistance, the measured data is related
to the real temperature as follows:
T
T
n
n
T
T
ACTUAL
M
NOMINAL
M
M
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
=
1
1 009
1 002
1 00699
.
.
( .
)
T   T
n
n
M
ACTUAL
NOMINAL
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
1
相關PDF資料
PDF描述
MAX6695YAUB+ IC SENSOR TEMP SMBUS 10-UMAX
MAX6697UP38+ IC TEMP MON 7CH PREC 20TSSOP
MAX6698UE99+ IC TEMP MONITOR 7CH 16-TSSOP
MAX6699EE34+ IC TEMP MONITOR 5CH 16-QSOP
MAX7500MTA+T IC TEMP SENSOR DGTL 8TDFN
相關代理商/技術參數
參數描述
MAX6694UE9A+ 功能描述:板上安裝溫度傳感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6694UE9A+T 功能描述:板上安裝溫度傳感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6695AUB 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6695AUB+ 功能描述:板上安裝溫度傳感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6695AUB+C5L 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*