參數資料
型號: MAX6690MEE+
廠商: Maxim Integrated
文件頁數: 14/16頁
文件大?。?/td> 149K
描述: IC TEMP SENSOR SMBUS 16-QSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 100
功能: 溫度計,恒溫計
傳感器類型: 內部和外部
感應溫度: -55°C ~ 125°C,外部傳感器
精確度: ±5°C(最小值)
拓撲: ADC,多路復用器,寄存器庫
輸出類型: I²C?/SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 5.5 V
工作溫度: -55°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-QSOP
包裝: 管件
2癈 Accurate Remote/Local Temperature
Sensor with SMBus Serial Interface
14   ______________________________________________________________________________________
The MAX6690 incorporates collision avoidance so that
completely asynchronous operation is allowed between
SMBus operations and temperature conversions.
When autoconverting, if the T
HIGH
and T
LOW
limits are
close together, its possible for both high-temp and low-
temp status bits to be set, depending on the amount of
time between status read operations (especially when
converting at the fastest rate). In these circumstances,
it is best not to rely on the status bits to indicate rever-
sals in long-term temperature changes. Instead, use a
current temperature reading to establish the trend
direction.
Conversion Rate Byte
The conversion rate register (Table 8) programs the
time interval between conversions in free-running auto-
convert mode. This variable rate control can be used to
reduce the supply current in portable-equipment appli-
cations. The conversion rate bytes POR state is 02h
(0.25Hz). The MAX6690 looks only at the 3LSB bits of
this register, so the upper 5 bits are dont care bits,
which should be set to zero. The conversion rate toler-
ance is ?5% at any rate setting.
Valid A/D conversion results for both channels are
available one total conversion time (125ms nominal,
156ms maximum) after initiating a conversion, whether
conversion is initiated through the RUN/STOP bit, hard-
ware STBY/pin, one-shot command, or initial power-up.
Extended resolution and the parasitic resistance can-
cellation mode are available at conversion rates of 1Hz
or lower.
Slave Addresses
The MAX6690s device address can be set to one of
nine different values by pin strapping ADD0 and ADD1
so that more than one MAX6690 can reside on the
same bus without address conflicts (Table 9).
The address pin states are checked at POR only, and
the address data stays latched to reduce quiescent
supply current due to the bias current needed for high-
Z state detection.
The MAX6690 also responds to the SMBus Alert
Response slave address (see the Alert Response
Address section).
POR and UVLO
The MAX6690 has a volatile memory. To prevent
ambiguous power-supply conditions from corrupting
the data in memory and causing erratic behavior, a
POR voltage detector monitors V
CC
and clears the
memory if V
CC
falls below 2V (typ, see Electrical
Characteristics). When power is first applied and V
CC
rises above 2.0V (typ), the logic blocks begin operat-
ing, although reads and writes at V
CC
levels below 3V
are not recommended. A second V
CC
comparator, the
ADC undervoltage lockout (UVLO) comparator, pre-
vents the ADC from converting until there is sufficient
headroom (V
CC
= 2.8V typ).
BIT
NAME
POR
STATE
FUNCTION
7 (MSB)
BUSY
0
ADC is busy converting when high.
6
LHIGH
0
Internal high-temperature alarm has tripped when high; cleared by POR or readout
of the entire status byte if the fault condition no longer exists.
5
LLOW
0
Internal low-temperature alarm has tripped when high; cleared by POR or readout of
the entire status byte if the fault condition no longer exists.
4
RHIGH
0
External high-temperature alarm has tripped when high; cleared by POR or readout
of the entire status byte if the fault condition no longer exists.
3
RLOW
0
External low-temperature alarm has tripped when high; cleared by POR or readout
of the entire status byte if the fault condition no longer exists.
2
OPEN
0
A high indicates an external diode is open; cleared by POR or readout of the entire
status byte if the fault condition no longer exists.
1 or 0
RFU
0
Reserved.
Table 7. Status Byte Bit Assignments
相關PDF資料
PDF描述
MAX6692YMSA+ IC SENSOR REMOTE SMBUS 8SOIC
MAX6693UP9A+T IC TEMP MONITOR 7CH 20-TSSOP
MAX6694TE9A+T IC TEMP MONITOR 5CH 16TQFN
MAX6695YAUB+ IC SENSOR TEMP SMBUS 10-UMAX
MAX6697UP38+ IC TEMP MON 7CH PREC 20TSSOP
相關代理商/技術參數
參數描述
MAX6690MEE+ 功能描述:板上安裝溫度傳感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6690MEE+T 功能描述:板上安裝溫度傳感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6690MEE-T 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6690YMEE+ 功能描述:板上安裝溫度傳感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6690YMEE+T 功能描述:板上安裝溫度傳感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor