- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6689UP34+ (Maxim Integrated)IC 7CH PREC TEMP MONITOR 20TSSOP Datasheet資料下載
參數資料
| 型號： | MAX6689UP34+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 14/19頁 |
| 文件大?。?/td> | 240K |
| 描述： | IC 7CH PREC TEMP MONITOR 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 74 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±1°C 本地（最大），±3°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC，緩沖器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁
Unused Diode Channels
If one or more of the remote diode channels is not
needed, the DXP and DXN inputs for that channel
should either be unconnected, or the DXP input should
be connected to V
CC
. The status register indicates a
diode "fault" for this channel and the channel is ignored
during the temperature-measurement sequence. It is
also good practice to mask any unused channels
immediately upon power-up by setting the appropriate
bits in the Configuration 2 and Configuration 3 regis-
ters. This will prevent unused channels from causing
ALERT or OVERT to assert.
Thermal Mass and Self-Heating
When sensing local temperature, the MAX6689 mea-
sures the temperature of the printed-circuit board
(PCB) to which it is soldered. The leads provide a good
thermal path between the PCB traces and the die. As
with all IC temperature sensors, thermal conductivity
between the die and the ambient air is poor by compar-
ison, making air temperature measurements impracti-
cal. Because the thermal mass of the PCB is far greater
than that of the MAX6689, the device follows tempera-
ture changes on the PCB with little or no perceivable
delay. When measuring the temperature of a CPU or
other IC with an on-chip sense junction, thermal mass
has virtually no effect; the measured temperature of the
junction tracks the actual temperature within a conver-
sion cycle.
When measuring temperature with discrete remote
transistors, the best thermal response times are
obtained with transistors in small packages (i.e., SOT23
or SC70). Take care to account for thermal gradients
between the heat source and the sensor, and ensure
that stray air currents across the sensor package do
not interfere with measurement accuracy. Self-heating
does not significantly affect measurement accuracy.
Remote-sensor self-heating due to the diode current
source is negligible.
7-Channel Precision Temperature Monitor
14 ______________________________________________________________________________________
Table 7. Status 1 Register
BIT
NAME
POR
STATE
FUNCTION
7 (MSB)
Reserved
0
6
Local ALERT
0
Local Channel High-Alert Bit. This bit is set to logic 1 when the local
temperature exceeds the temperature threshold limit in the local ALERT high-
limit register.
5
Remote 6 ALERT
0
Channel 6 Remote-Diode High-Alert Bit. This bit is set to logic 1 when the
channel 6 remote-diode temperature exceeds the temperature threshold limit
in the remote 6 ALERT high-limit register.
4
Remote 5 ALERT
0
Channel 5 Remote-Diode High-Alert Bit. This bit is set to logic 1 when the
channel 5 remote-diode temperature exceeds the programmed temperature
threshold limit in the remote 5 ALERT high-limit register.
3
Remote 4 ALERT
0
Channel 4 Remote-Diode High-Alert Bit. This bit is set to logic 1 when the
channel 4 remote-diode temperature exceeds the temperature threshold limit
in the remote 4 ALERT high-limit register.
2
Remote 3 ALERT
0
Channel 3 Remote-Diode High-Alert Bit. This bit is set to logic 1 when the
channel 3 remote-diode temperature exceeds the programmed temperature
threshold limit in the remote 3 ALERT high-limit register.
1
Remote 2 ALERT
0
Channel 2 Remote-Diode High-Alert Bit. This bit is set to logic 1 when the
channel 2 remote-diode temperature exceeds the temperature threshold limit
in the remote 2 ALERT high-limit register.
0
Remote 1 ALERT
0
Channel 1 Remote-Diode High-Alert Bit. This bit is set to logic 1 when the
channel 1 remote-diode temperature exceeds the temperature threshold limit
in the remote 1 ALERT high-limit register.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6690MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6692YMSA+ | IC SENSOR REMOTE SMBUS 8SOIC |
| MAX6693UP9A+T | IC TEMP MONITOR 7CH 20-TSSOP |
| MAX6694TE9A+T | IC TEMP MONITOR 5CH 16TQFN |
| MAX6695YAUB+ | IC SENSOR TEMP SMBUS 10-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6689UP34+ | 功能描述:板上安裝溫度傳感器 7Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6689UP34+T | 功能描述:板上安裝溫度傳感器 7Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6689UP34-T | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Tape and Reel |
| MAX6689UP38 | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Rail/Tube |
| MAX6689UP38-T | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。