- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6664AEE+T (Maxim Integrated)IC TEMP MON FAN CNTRL 16-QSOP Datasheet資料下載
參數資料
| 型號： | MAX6664AEE+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 12/24頁 |
| 文件大小： | 297K |
| 描述： | IC TEMP MON FAN CNTRL 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±2°C 本地（最大），±3°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫，測速計 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
Temperature Monitors and
PWM Fan Controllers
12 ______________________________________________________________________________________
measurement rate, which is controlled by bits [4:2] of
the fan-filter register (23h). Table 5 shows the effect of
the temperature measurement rate control bits. As an
example, assume that the temperature measurement
rate is 2Hz, or 0.5s per monitoring cycle, and the fan-fil-
ter rate is 0.416% per monitoring cycle. For the fan drive
to change from 50% to 100% requires 50% / 0.416% =
120 temperature monitoring cycles. Thus, for a tempera-
ture-monitoring cycle of 0.5s, the time required for the
drive to change from 50% to 100% is 60s.
Fan-Speed Measurement
The fan speed is measured by using the relatively slow
tachometer signal from the fan to gate an 11.25kHz
clock frequency into a fan-speed counter. The mea-
surement is initialized on the starting edge of a PWM
output if fan-speed measurement is enabled by setting
bit 2 of configuration register 2 (01h) to 1. Counting
begins on the leading edge of the second tachometer
pulse and lasts for two tachometer periods or until the
counter overranges (255). The measurement repeats
unless monitoring is disabled by resetting bit 2 in the
configuration register 2 (01h). The measured result is
stored in the fan-speed reading register (08h).
The fan-speed count is given by:
The fan-speed count is given by:
where RPM = fan speed in RPM.
N determines the speed range and is programmed by
bits [7:6] in the fan characteristics register (20h) as
shown in Table 14. When the speed falls below the value
in the speed range column, a fan failure is detected.
The TACH/AIN input can be either a digital signal (from
the fans tachometer output) or an analog signal,
depending on the setting of bit 2 of the configuration
register 1 (00h). The default setting is zero, which sets
up TACH/AIN as a digital input. For the analog input
(Figure 4), the detected voltage threshold is typically at
250mV, which is appropriate for sensing the voltage of
a sense resistor connected to the ground lead of a 2-
wire fan. The AIN input only responds to pulse widths
greater than 10祍.
Count
RPM N
=
?/DIV>
675000
,
Table 12. Spin-Up Time; Bits [2:0] Fan
Characteristics Register (20h)POR = 101
BIT 2
BIT 1
BIT 0
SPIN-UP
TIME (s)
0
0
0
0.2
0
0
1
0.4
0
1
0
0.6
0
1
1
0.8
1
0
0
1
1
0
1
2
1
1
0
4
1
1
1
8
Table 13. Fan Filter Ramp Rate; Bits [6:5]
Fan Filter Register (23h)POR = 10;
BIT 6
BIT 5
RAMP RATE
x100% / 240
RAMP RATE
% DUTY CYCLE
0
0
1
0.416
0
1
2
0.833
1
0
4
1.667
1
1
8
3.333
FAN CHARACTERISTICS REGISTER (20h) POR = 01
BIT 7
BIT 6
N
SPEED RANGE (FAIL SPEED)
(RPM)
0
0
1
2647
0
1
2
1324
1
0
4
662
1
1
8
331
Table 14. N Factor for Speed-Range Adjustment (Assuming Two Tachometer Pulses
per Revolution)
Figure 4. Simplified Tachometer Analog Input Structure
100&
VREF 1
0.1礔
TACH
INPUT
VREF 2
CLK
FF
MAX6653
MAX6663
MAX6664
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6665ASA45+ | IC FAN CNTRL/DRVR 8-SOIC |
| MAX6670AUB45+ | IC TEMP SENSOR REMOTE 10-UMAX |
| MAX6678AEP92+ | IC TEMP MONITOR 2CH PWM 20-QSOP |
| MAX6681MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6689UP34+ | IC 7CH PREC TEMP MONITOR 20TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6664AEE-TG075 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX6665ASA070 | 制造商:Maxim Integrated Products 功能描述: |
| MAX6665ASA40 | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6665ASA40+ | 功能描述:馬達/運動/點火控制器和驅動器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6665ASA40+T | 功能描述:馬達/運動/點火控制器和驅動器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。