- 您現在的位置：買賣IC網 > PDF目錄67801 > MAX6651EEE+ (MAXIM INTEGRATED PRODUCTS INC) Fan-Speed Regulators and Monitors with SMBus™/I<sup>2</sup>C-Compatible Interface PDF資料下載
參數資料
| 型號： | MAX6651EEE+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Fan-Speed Regulators and Monitors with SMBus™/I<sup>2</sup>C-Compatible Interface |
| 中文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.1 A, PDSO16 |
| 封裝： | QSOP-16 |
| 文件頁數： | 8/25頁 |
| 文件大?。?/td> | 235K |
| 代理商： | MAX6651EEE+ |
downtime. The system should be designed so that the
number of fans used is one more than are actually
needed. This way, there is sufficient cooling even if a
fan fails. With all fans operating correctly, it is unneces-
sary to run the fans at their maximum speed. Reducing
fan speed can reduce noise and increase the life of the
fans. However, once a fan fails, it is important that the
remaining fans spin at their maximum speed.
In Figure 9, all the GPIO0s are configured as ALERT
outputs, and all the GPIO1s are configured as
FULL ON inputs. If any MAX6650 generates an ALERT
(indicating failure), the remaining MAX6650s will auto-
matically turn their fans on full.
Temperature Monitoring and Fan Control
The circuit shown in Figure 10 provides complete tem-
perature monitoring and fan control. The MAX1617A (a
remote/local temperature serial interface with SMBus)
monitors temperature with a diode-connected transis-
tor. Based on the temperature readings provided by
the MAX1617A, the C can adjust the fan speed pro-
portionally with temperature. Connecting the ALERT
output of the MAX1617A to the FULL ON input of the
MAX6650/MAX6651 (see the
General-Purpose Input/
Output section) allows the fan to turn on fully if the
MAX1617A detects an overtemperature condition.
MAX6501 Hardware Fail-Safe
Figure 11 shows an application using a MAX6501 as a
hardware fail-safe. The MAX6650 has its GPIO1 config-
ured as FULL ON input. The MAX6501 TOVER pin goes
low whenever its temperature goes above a preset value.
This pulls the FULL ON pin (GPIO1) low, forcing the fan to
spin at its maximum speed. Figure 12 shows the use of
multiple MAX6501s. The MAX6501 has an open-drain
output, allowing multiple devices to be wire ORed to the
FULL ON input. This configuration allows fail-safe moni-
toring of multiple locations around the system.
Hot-Swap Application
Hot swapping of a fan can be detected using the circuit
in Figure 13 where GPIO2 is configured to generate an
alert whenever it is pulled low. As long as the fan card
is connected, GPIO2 is high. However, when the fan
card is removed, a 2.2k
Ω resistor pulls GPIO2 low,
causing an interrupt. This signals to the system that a
hot swap is occurring.
Step-by-Step Part Selection
and Software Setup
Determining the Fan System Topology
The MAX6650/MAX6651 support three fan system
topologies. These are single fan control, parallel fan
control, and synchronized fan control.
Single Fan Control
The simplest configuration is a single MAX6650 for
each fan. If two or more fans are required per system,
then additional MAX6650 controllers are used (one per
fan). The advantage of this configuration is the ability to
MAX6650/MAX6651
Fan-Speed Regulators and Monitors
with SMBus/I2C-Compatible Interface
16
______________________________________________________________________________________
MAX6650
GPIO1
MAX6650
GPIO1
MAX6650
GPIO1
FAN
1
FAN
2
FAN
3
MAX6650
GPIO1
FAN
4
GPIO0
ALERT
FULL ON
ALERT
FULL ON
TO INT PIN
ON NC
Figure 9. N + 1 Application
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6652AUB+ | Temperature Sensor and System Monitor in a 10-Pin µMAX |
| MAX6652AUB+T | Temperature Sensor and System Monitor in a 10-Pin µMAX |
| MAX6654MEE+ | 1°C Accurate Remote/Local Temperature Sensor with SMBus Serial Interface |
| MAX6654YMEE+ | 1°C Accurate Remote/Local Temperature Sensor with SMBus Serial Interface |
| MAX6655MEE+ | Dual Remote/Local Temperature Sensors and Four-Channel Voltage Monitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6651EEE+ | 功能描述:馬達/運動/點火控制器和驅動器 Fan-Speed Regulator & Monitor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6651EEE+T | 功能描述:馬達/運動/點火控制器和驅動器 Fan-Speed Regulator & Monitor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6651EEE+TG074 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX6651EEE-T | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MAX6651EVCMAXQU | 功能描述:電源管理模塊 MAX6651 Evaluation Kit/Evaluation System RoHS:否 制造商:ROHM Semiconductor 產品:AC-DC Converters 最大輸入電壓:264 VAC 開關頻率: 輸出電壓:10 V to 28.8 V 輸出電流:350mA 負載調節: 最大工作溫度:+ 60 C 尺寸:100 mm x 16 mm x 17 mm |
發布緊急采購，3分鐘左右您將得到回復。