- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6642ATT94+T (Maxim Integrated)IC TEMP SENSOR SMBUS 6TDFN Datasheet資料下載
參數資料
| 型號： | MAX6642ATT94+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 154K |
| 描述： | IC TEMP SENSOR SMBUS 6TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，0°C ~ 150°C |
| 精確度： | ±3°C（最小值） |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-WDFN 裸露焊盤 |
| 供應商設備封裝： | 6-TDFN 裸露焊盤（3x3） |
| 包裝： | 帶卷 (TR) |
tion rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledge and continues to hold the ALERT line low
until cleared. (The conditions for clearing an ALERT
vary depending on the type of slave device.)
Successful completion of the alert response protocol
clears the interrupt latch. If the condition still exists, the
device reasserts the ALERT interrupt at the end of the
next conversion.
Command Byte Functions
The 8-bit command byte register (Table 3) is the master
index that points to the various other registers within the
MAX6642. The registers POR state is 0000 0000, so a
Receive Byte transmission (a protocol that lacks the
command byte) that occurs immediately after POR
returns the current local temperature data.
Single-Shot
The single-shot command immediately forces a new
conversion cycle to begin. If the single-shot command
is received while the MAX6642 is in standby mode
(RUN bit = 1), a new conversion begins, after which the
device returns to standby mode. If a single-shot con-
version is in progress when a single-shot command is
received, the command is ignored. If a single-shot
command is received in autonomous mode (RUN bit =
0), the command is ignored.
Configuration Byte Functions
The configuration byte register (Table 4) is a read-write
register with several functions. Bit 7 is used to mask
(disable) interrupts. Bit 6 puts the MAX6642 into stand-
by mode (STOP) or autonomous (RUN) mode. Bit 5 dis-
ables local temperature conversions for faster (8Hz)
remote temperature monitoring. Bit 4 prevents setting
the ALERT output until two consecutive measurements
result in fault conditions.
Status Byte Functions
The status byte register (Table 5) indicates which (if
any) temperature thresholds have been exceeded. This
byte also indicates whether the ADC is converting and
whether there is an open-circuit fault detected on the
external sense junction. After POR, the normal state of
all flag bits is zero, assuming no alarm conditions are
present. The status byte is cleared by any successful
read of the status byte after the overtemperature fault
condition no longer exists.
Slave Addresses
The MAX6642 has eight fixed addresses available.
These are shown in Table 6.
The MAX6642 also responds to the SMBus alert
response slave address (see the Alert Response
Address section).
POR and UVLO
To prevent ambiguous power-supply conditions from
corrupting the data in memory and causing erratic
behavior, a POR voltage detector monitors V
CC
and
clears the memory if V
CC
falls below 2.1 (typ). When
power is first applied and V
CC
rises above 2.1 (typ),
the logic blocks begin operating, although reads and
writes at V
CC
levels below 3V are not recommended. A
second V
CC
comparator, the ADC undervoltage lockout
(UVLO) comparator prevents the ADC from converting
until there is sufficient headroom (V
CC
= +2.7V typ).
Power-Up Defaults
Power-up defaults include:
" ALERT output is cleared.
" ADC begins autoconverting at a 4Hz rate.
" Command byte is set to 00h to facilitate quick
local Receive Byte queries.
" Local (internal) T
HIGH
limit set to +70癈.
" Remote (external) T
HIGH
limit set to +120癈.
Applications Information
Remote-Diode Selection
The MAX6642 can directly measure the die temperature
of CPUs and other ICs that have on-board temperature-
sensing diodes (see the Typical Operating Circuit) or
they can measure the temperature of a discrete diode-
connected transistor.
Effect of Ideality Factor
The accuracy of the remote temperature measurements
depends on the ideality factor (n) of the remote diode
(actually a transistor). The MAX6642 is optimized for n
= 1.008, which is the typical value for the Intel Pentium
?癈, SMBus-Compatible Remote/Local
Temperature Sensor with Overtemperature Alarm
_______________________________________________________________________________________ 9
PART NO. SUFFIX
ADDRESS
MAX6642ATT90
1001 000
MAX6642ATT92
1001 001
MAX6642ATT94
1001 010
MAX6642ATT96
1001 011
MAX6642ATT98
1001 100
MAX6642ATT9A
1001 101
MAX6642ATT9C
1001 110
MAX6642ATT9E
1001 111
Table 6. Slave Address
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6643LBFAEE+ | IC CTLR PWM FAN-SPEED 16QSOP |
| MAX6649MUA/V+ | IC SENSOR REMOTE SMBUS 8UMAX |
| MAX6652AUB+T | IC TEMP SENS/MON 10-UMAX |
| MAX6659MEE+T | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6661AEE+T | IC REG FAN SPEED 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6642ATT96+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6642ATT96-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6642ATT98 | 制造商:Maxim Integrated Products 功能描述:1 C SMBUS-COMPATIBLE REMOTE/LOCAL TEMPERATURE SENSOR WITH O - Rail/Tube |
| MAX6642ATT98+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 6TDFN EP - Rail/Tube |
| MAX6642ATT98+T | 功能描述:板上安裝溫度傳感器 SMBus-Compatible Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。