參數資料
型號： MAX6639FATE+
廠商： Maxim Integrated
文件頁數： 19/22頁
文件大小： 234K
描述： IC 2CH TEMP MONITOR 16TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 60
功能： 風扇控制，溫度監控器
傳感器類型： 內部和外部
感應溫度： 0°C ~ 150°C，外部傳感器
精確度： -2.5°C 本地（最大），±1°C 遠程（最大）
拓?fù)洌?/td> ADC，PWM 發生器，轉速計計數器
輸出類型： I²C?/SMBus?
輸出警報： 是
輸出風扇： 是
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-WQFN 裸露焊盤
供應商設備封裝： 16-TQFN-EP（5x5）
包裝： 管件
Effect of Series Resistance
Series resistance in a sense diode contributes addition-
al errors. For nominal diode currents of 10礎 and
100礎, change in the measured voltage is:
擵
M
= R
S
(100礎 - 10礎) = 90礎 x R
S
Since 1癈 corresponds to 198.6礦, series resistance
contributes a temperature offset of:
Assume that the diode being measured has a series
resistance of 3? The series resistance contributes an
offset of:
The effects of the ideality factor and series resistance
are additive. If the diode has an ideality factor of 1.002
and series resistance of 3? the total offset can be cal-
culated by adding error due to series resistance with
error due to ideality factor:
1.36癈 - 2.13癈 = -0.77癈
for a diode temperature of +85癈.
In this example, the effect of the series resistance and
the ideality factor partially cancel each other.
For best accuracy, the discrete transistor should be a
small-signal device with its collector connected to GND
and base connected to DXN. Table 12 lists examples of
discrete transistors that are appropriate for use with the
MAX6639.
The transistor must be a small-signal type with a rela-
tively high forward voltage; otherwise, the ADC input
voltage range can be violated. The forward voltage at
the highest expected temperature must be greater than
0.25V at 10礎, and at the lowest expected temperature,
the forward voltage must be less than 0.95V at 100礎.
Large-power transistors must not be used. Also, ensure
that the base resistance is less than 100? Tight speci-
fications for forward current gain (50 <  < 150, for
example) indicate that the manufacturer has good
process controls and that the devices have consistent
V
BE
characteristics.
ADC Noise Filtering
The integrating ADC has inherently good noise rejec-
tion, especially of low-frequency signals such as
60Hz/120Hz power-supply hum. Micropower operation
places constraints on high-frequency noise rejection.
Lay out the PCB carefully with proper external noise fil-
tering for high-accuracy remote measurements in elec-
trically noisy environments.
Filter high-frequency electromagnetic interference
(EMI) at DXP and DXN with an external 2200pF capaci-
tor connected between the two inputs. This capacitor
can be increased to approximately 3300pF (max),
including cable capacitance. A capacitance higher
than 3300pF introduces errors due to the rise time of
the switched-current source.
Twisted Pairs and Shielded Cables
For remote-sensor distances longer than 8in, or in par-
ticularly noisy environments, a twisted pair is recom-
mended. Its practical length is 6ft to 12ft (typ) before
noise becomes a problem, as tested in a noisy elec-
tronics laboratory. For longer distances, the best solu-
tion is a shielded twisted pair like that used for audio
microphones. For example, Belden #8451 works well
for distances up to 100ft in a noisy environment.
Connect the twisted pair to DXP and DXN and the
shield to ground, and leave the shields remote end
unterminated. Excess capacitance at DXN or DXP limits
practical remote-sensor distances (see the Typical
Operating Characteristics).
For very long cable runs, the cables parasitic capaci-
tance often provides noise filtering, so the recommend-
ed 2200pF capacitor can often be removed or reduced
in value. Cable resistance also affects remote-sensor
accuracy. A 1?series resistance introduces about
+1/2癈 error.
PCB Layout Checklist
1)  Place the MAX6639 as close as practical to the
remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 4in to
8in, or more, as long as the worst noise sources
(such as CRTs, clock generators, memory buses,
and ISA/PCI buses) are avoided.
2)  Do not route the DXP/DXN lines next to the deflection
coils of a CRT. Also, do not route the traces across a
fast memory bus, which can easily introduce +30癈
error, even with good filtering. Otherwise, most noise
sources are fairly benign.
3   0 453
1 36
┳
?/DIV>
?/DIV>
=
?/DIV>
.
    .
C
C
90
198 6
0 453
?/DIV>
?/DIV>
?/DIV>
?/DIV>
=
?/DIV>
?/DIV>
V
V
C
C
.
      .
2-Channel Temperature Monitor with Dual,
Automatic, PWM Fan-Speed Controller
Maxim Integrated
19
MAX6639/MAX6639F
相關PDF資料
PDF描述
MAX6641AUB92+ IC TEMP MONITOR SMBUS 10UMAX
MAX6642ATT94+T IC TEMP SENSOR SMBUS 6TDFN
MAX6643LBFAEE+ IC CTLR PWM FAN-SPEED 16QSOP
MAX6649MUA/V+ IC SENSOR REMOTE SMBUS 8UMAX
MAX6652AUB+T IC TEMP SENS/MON 10-UMAX
相關代理商/技術參數
參數描述
MAX6639FATE+ 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6639FATE+T 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6639YAEE+ 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX6639YAEE+T 功能描述:板上安裝溫度傳感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MAX663C/D 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*