- 您現在的位置：買賣IC網 > PDF目錄67798 > MAX6505UTN015+ (MAXIM INTEGRATED PRODUCTS INC) Dual Trip SOT Temperature Switches PDF資料下載
參數資料
| 型號： | MAX6505UTN015+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Dual Trip SOT Temperature Switches |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO6 |
| 封裝： | ROHS COMPLIANT, SOT-23, 6 PIN |
| 文件頁數： | 19/23頁 |
| 文件大?。?/td> | 405K |
| 代理商： | MAX6505UTN015+ |
MAX6505–MAX6508
Dual Trip SOT Temperature Switches
_______________________________________________________________________________________
5
_______________Detailed Description
The MAX6505–MAX6508 fully integrated temperature
switches incorporate two temperature-dependent refer-
ences and a comparator. One reference exhibits a pos-
itive temperature coefficient and the other a negative
temperature coefficient. The temperature at which the
two reference voltages are equal determines the tem-
perature trip point. There are two versions, each of
which has two logic outputs.
The MAX6505/MAX6506 have a main trip point (TALARM)
and a lower, “warning” trip point (TWARN). When the die
temperature rises above these trip points, the ALARM
and WARN outputs are asserted (Figure 1). The differ-
ence between the two trip points (
TAW) is pin selec-
table to +5°C, +10°C, +20°C, or +30°C by connecting
the two control pins (S0 and S1) high or low (Table 1).
MAX6505 has open-drain active-low outputs; MAX6506
has push-pull active-high outputs.
The MAX6507/MAX6508 have two factory-programmed
threshold temperatures (TOVER and TUNDER) and two
outputs (OK and OVER). One output (OK) asserts
when the temperature is between TOVER and TUNDER.
The other output (OVER) asserts when the temperature
is above TOVER. Table 4 shows the hex codes to deter-
mine the part numbers associated with specific values
of TOVER and TUNDER. The first hex code indicates the
lower trip point (TUNDER) and the second indicates the
higher trip point (TOVER). For example, a part with TUN-
DER = -10°C and TOVER = +75°C will have the part
number MAX6508UTA04B (Table 4 and Figure 2).
MAX6507 has open-drain outputs; MAX6508 has push-
pull outputs.
Hysteresis Selection
The temperature threshold hysteresis for the ALARM
output of the MAX6505/MAX6506 is 2°C. The hysteresis
for the WARN output depends on the value of
TAW. If
TAW is 5°C or 10°C (set by S0 and S1), WARN hys-
teresis is 5°C. If
TAW is 20°C or 30°C, WARN hystere-
sis is 10°C. MAX6507 and MAX6508 have pin-selectable
hysteresis of 2°C or 10°C for both OVER and OK out-
puts (Table 2).
Applications Information
Thermal Considerations
The MAX6505–MAX6508 supply current is typically
30A. When used to drive high-impedance loads, the
devices dissipate negligible power. Therefore, the die
temperature is essentially the same as the package
temperature. The key to accurate temperature monitor-
ing is good thermal contact between the MAX6505–
MAX6508 package and the device being monitored. In
some applications, the SOT23-6 packages may be
small enough to fit underneath a socketed micro-
processor (P), allowing the device to monitor the P’s
temperature directly. Use the monitor’s output to reset
the P, assert an interrupt, or trigger an external alarm.
Accurate temperature monitoring depends on the ther-
mal resistance between the device being monitored
and the MAX6505–MAX6508 die.
The rise in die temperature due to self-heating is given
by the following formula:
TJ = PDISSIPATION θJA
where PDISSIPATION is the power dissipated by the
MAX6505–MAX6508, and
θJA is the package’s thermal
resistance. The typical thermal resistance is +115°C/W
for the SOT23-6 package. To limit the effects of self-heat-
ing, minimize the output currents. For example, if the
MAX6505 sinks 5mA, the output voltage is guaranteed to
be less than 0.5V. Therefore, an additional 2.5mW of
Figure 1. Temperature Response—MAX6505UTP065 Outputs,
TAW = 10°C, and WARN Hysteresis ≈ 5°C
HYSTERESIS
≈ 2°C
HYSTERESIS
≈ 5°C
65°C
55°C
WARN
ALARM
Table 1. MAX6505/MAX6506
TAW
Selection Table
CONTROL PINS
DESCRIPTION
S0
S1
TAW =TALARM – TWARN
(
°C)
GND
5
GND
VCC
10
VCC
GND
20
VCC
30
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6505UTN020+ | Dual Trip SOT Temperature Switches |
| MAX6505UTN025+ | Dual Trip SOT Temperature Switches |
| MAX6505UTN030+ | Dual Trip SOT Temperature Switches |
| MAX6505UTN035+ | Dual Trip SOT Temperature Switches |
| MAX6505UTP000+ | Dual Trip SOT Temperature Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6505UTN015+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 6PIN SOT-23 - Rail/Tube |
| MAX6505UTN015+T | 功能描述:板上安裝溫度傳感器 Dual Trip Temperature Switch RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6505UTN015-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6505UTN020+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 6PIN SOT-23 - Rail/Tube |
| MAX6505UTN020+T | 功能描述:板上安裝溫度傳感器 Dual Trip Temperature Switch RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。