- 您現在的位置：買賣IC網 > PDF目錄180529 > MAX6453UT23S+T (MAXIM INTEGRATED PRODUCTS INC) µP Supervisors with Separate VCC Reset and Manual Reset Outputs PDF資料下載
參數資料
| 型號： | MAX6453UT23S+T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | µP Supervisors with Separate VCC Reset and Manual Reset Outputs |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | LEAD FREE, SOT-23, 6 PIN |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 249K |
| 代理商： | MAX6453UT23S+T |
MAX6453–MAX6456
P Supervisors with Separate VCC Reset and
Manual Reset Outputs
6
_______________________________________________________________________________________
Detailed Description
Reset Output
The reset output is typically connected to the reset
input of a microprocessor (P). A P’s reset input starts
or restarts the P in a known state. The MAX6453–
MAX6456 P supervisory circuits provide the reset
logic to prevent code-execution errors during power-
up, power-down and brownout conditions (see the
Typical Operating Circuit).
RESET changes from high to low whenever the moni-
tored voltage (RSTIN or VCC) drops below the reset
threshold voltages. When VRSTIN and VCC exceed their
respective reset threshold voltages, RESET remains low
for the reset timeout period, and then goes high. RESET
changes from high to low after MR input is held low for
the extended (typ) setup timeout period and deasserts
140ms (min) after MR deasserts.
RESET is guaranteed to be in the proper output logic
state for VCC inputs
≥ 1V. For applications requiring valid
reset logic when VCC is less than 1V, see the Ensuring a
Valid RESET Output Down to VCC = 0V section.
Manual Reset
The MAX6453/MAX6454 contain a manual reset output
(MROUT) that asserts low immediately after driving MR
low and remains low for the reset timeout period after
MR goes high (Figure 1). The pushbutton manual reset
has no effect on the RESET output. MROUT output can
be used to drive an NMI (nonmaskable interrupt) on the
processor to save valuable data.
The MAX6455/MAX6456’s MROUT is asserted immedi-
ately upon driving MR low. Driving MR low for longer
than the extended (typ) setup timeout period asserts
RESET. When MR is deasserted, MROUT and RESET
remain asserted low for the reset timeout period after
MR goes high (Figure 2).
Adjustable Input Voltage (RSTIN)
The MAX6453–MAX6456 monitor the voltage on RSTIN
using an adjustable reset threshold set with an external
resistor voltage divider (Figure 3). Use the following for-
mula to calculate the externally monitored voltage
(VMON-TH):
VMON-TH = VTH-RSTIN (R1 +R2)/R2
where VMON_TH is the desired reset threshold voltage
and VTH-RSTIN is the reset input threshold (0.63V).
Resistors R1 and R2 can have very high values to mini-
mize current consumption due to low leakage currents.
Set R2 to some conveniently high value (250k
Ω, for
example) and calculate R1 based on the desired reset
threshold voltage, using the following formula:
R1 = R2 (VMON_TH/VTH - 1)
Ω
210ms
MROUT
RESET
MR
LONG SETUP PERIOD
Figure 2. MAX6455/MAX6456 Timing Diagram
210ms
MROUT
MR
Figure 1. MAX6453/MAX6454 Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6453UT26S+T | µP Supervisors with Separate VCC Reset and Manual Reset Outputs |
| MAX6453UT29S+ | µP Supervisors with Separate VCC Reset and Manual Reset Outputs |
| MAX6453UT29S+T | µP Supervisors with Separate VCC Reset and Manual Reset Outputs |
| MAX6453UT46S+T | µP Supervisors with Separate VCC Reset and Manual Reset Outputs |
| MAX6454UT16S+ | µP Supervisors with Separate VCC Reset and Manual Reset Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6453UT26S | 制造商:Maxim Integrated Products 功能描述:+P SUPERVISORS WITH SEPARATE VCC RE - Cut Tape Product 制造商:Rochester Electronics LLC 功能描述: |
| MAX6453UT26S+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR ADJV 7UA 6PIN SOT-23 - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX6453UT26S+T | 功能描述:監控電路 Dual uPower Reset Circuit RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6453UT26S-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6453UT29S | 制造商:Maxim Integrated Products 功能描述:+P SUPERVISORS WITH SEPARATE VCC RE - Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。