- 您現在的位置：買賣IC網 > PDF目錄383451 > MAX6323_UT__-T (Maxim Integrated Products, Inc.) レP Supervisory Circuits with Windowed (Min/Max) Watchdog and Manual Reset PDF資料下載
參數資料
| 型號： | MAX6323_UT__-T |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | レP Supervisory Circuits with Windowed (Min/Max) Watchdog and Manual Reset |
| 中文描述： | レP監控電路與窗口（最小/最大）看門狗和手動復位 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 717K |
| 代理商： | MAX6323_UT__-T |
M
falls below the preset threshold or when the manual
reset input (
MR)
is asserted. The
RESET
output remains
asserted for at least 100ms after V
CC
has risen above
the reset threshold and
MR
is deasserted (Figure 5).
For noisy environments, bybass V
CC
with a 500pF (min)
capacitor to ensure correct operation.
The MAX6323 has a push-pull output stage, and the
MAX6324 utilizes an open-drain output. Connect a pull-
up resistor on the
RESET
output of the MAX6324 to any
supply up to +6V. Select a resistor value large enough
to register a logic low (see
Electrical Characteristics
)
and small enough to register a logic high while supply-
ing all input leakage currents and leakage paths con-
nected to the
RESET
line. A 10k
pullup is sufficient in
most applications.
Manual Reset Input
Many μP-based products require manual reset capabil-
ity to allow an operator or external logic circuitry to initi-
ate a reset. The manual reset input (
MR
) can connect
directly to a switch without an external pullup resistor or
debouncing network.
MR
is internally pulled up to V
CC
and, therefore, can be left unconnected if unused.
MR
is designed to reject fast, negative-going transients
(typically 100ns pulses), and it must be held low for a
minimum of 1μs to assert the reset output (Figure 5). A
0.1μF capacitor from
MR
to ground provides additional
noise immunity. After
MR
transitions from low to high,
reset will remain asserted for the duration of the reset
timeout period, at least 100ms.
Applications Information
Negative-Going V
CC
Transients
The MAX6323/MAX6324 are relatively immune to short-
duration negative-going V
CC
transients (glitches),
which usually do not require the entire system to shut
down. Typically, 200ns large-amplitude pulses (from
ground to V
CC
) on the supply will not cause a reset.
Lower amplitude pulses result in greater immunity.
Typically, a V
CC
transient that falls 100mV below the
reset threshold and lasts less than 20μs will not trigger
a reset (see
Typical Operating Characteristics
). An
optional 0.1μF bypass capacitor mounted close to V
CC
provides additional transient immunity.
Ensuring a Valid Reset Output
Down to V
CC
= 0
When V
CC
falls below
+
1.2V, the MAX6323
RESET
out-
put no longer sinks current; it becomes an open circuit.
Therefore, high-impedance CMOS logic inputs con-
nected to
RESET
can drift to undetermined voltages.
This does not present a problem in most applications,
since most μPs and other circuitry are inoperative with
V
CC
below
+
1.2V. However, in applications where
RESET
must be valid down to 0, adding a pulldown
resistor to
RESET
causes any stray leakage currents to
flow to ground, holding
RESET
low (Figure 6). R1’s
value is not critical; 100k
is large enough not to load
RESET
and small enough to pull
RESET
to ground. This
scheme does not work with the open-drain output of the
MAX6324.
μP Supervisory Circuits with Windowed
(Min/Max) Watchdog and Manual Reset
8
_______________________________________________________________________________________
MR
RESET
V
CC
V
TH
100ms
(min)
120ns
(typ)
20
μ
s
(typ)
1
μ
s
(min)
100ms
(min)
Figure 5.
RESET
Timing Relationship
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6323 | Stereo Class-AB Audio Amplifier with Stereo Headphone Drive, Volume Control Memory 24-HTSSOP -40 to 85 |
| MAX6324_UT__-T | レP Supervisory Circuits with Windowed (Min/Max) Watchdog and Manual Reset |
| MAX6370KA-T | Pin-Selectable Watchdog Timers |
| MAX6369-MAX6374 | Pin-Selectable Watchdog Timers |
| MAX6374KA-T | Pin-Selectable Watchdog Timers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6324AUT23 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Cut Tape Product |
| MAX6324AUT23+T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6324AUT23-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6324AUT26 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Cut Tape Product |
| MAX6324AUT26+T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。