- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5922AEUI+ (Maxim Integrated)IC NETWORK PWR SW +48V 28-TSSOP Datasheet資料下載
參數資料
| 型號： | MAX5922AEUI+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 12/21頁 |
| 文件大?。?/td> | 437K |
| 描述： | IC NETWORK PWR SW +48V 28-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 是 |
| 電源電壓： | 32 V ~ 60 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1411 (CN2011-ZH PDF) |
+48V, Single-Port Network Power Switch
For Power-Over-LAN
12 ______________________________________________________________________________________
Detailed Description
The MAX5922 is a single-port network power controller
with an integrated power MOSFET, operating from a
+32V to +60V supply rail. The device is specifically
designed for PSE in power-over-LAN applications and is
fully compliant to the IEEE 802.3af standard. The
MAX5922 provides PD discovery, classification, current
limit, and other necessary functions for an IEEE 802.3af-
compliant PSE.
The MAX5922 operates in three different modes: PD
detection mode, PD classification mode, and power
mode. Figures 2 and 4 illustrates the devices functional
operation.
PD Detection Mode
Once powered up and enabled, the MAX5922 probes
the output for a valid PD. A valid PD should have a 25k&
discovery signature characteristic as specified in the
IEEE 802.3af standard. Table 1 shows the IEEE 802.3af
specification for a PSE detection of PDs (see the Typical
Application Circuit and Figure 3 (MAX5922 startup
sequence)).
The MAX5922 performs the PD detection by forcing a
probe voltage (V
PBI
= 4V) at the OUT pin and senses the
current out of this pin. The sensed current is sampled and
held t
DET
(88ms) after the probing voltage is sent. The
probe voltage is then switched to V
PBII
= 8V. At the end
of another t
DET
period, the ratio of the difference of the
two test voltages and sensed currents (V/I) is calculat-
ed to determine the PD resistance. The MAX5922 PD
detection circuitry checks for a valid PD resistive signa-
ture between 19k& and 26.5k&, with a parallel capaci-
tance of up to 0.6礔. The MAX5922 PD detection circuit
rejects all PDs showing resistive signature of less than
15k& or greater than 33k&, and/or a capacitive signature
greater than 6礔. Any resistive signature between 15k&
to 19k&, or between 26.5k& to 33k&, and/or a capaci-
tance between 0.6礔 to 6礔 can produce unpredictable
detection results. If the MAX5922 does not detect a valid
PD signature, it continually sends the probe voltages to
the output indefinitely (see Figure 5).
The detection current reference is set by an external
resistor (R
RDT)
) connected from the RDT pin to AGND.
This resistor should be an 18.2k& ?%, with an optional
680nF capacitor in parallel for filtering out power-line
noise. An internal diode in series with the detection volt-
age source and OUT is provided to restrict PD detec-
tion to the 1st quadrant as specified by the IEEE
standard 802.3af (see Figure 3). To prevent damage to
non-PD devices and to protect itself from output short
circuit, the MAX5922 limits the current out of the OUT
pin during PD detection to 1.5mA (max).
For midspan systems where power is delivered to the
PD through the spare pairs, the detection collision
avoidance must be activated. In this mode, after every
failed PD detection cycle, the MAX5922A/MAX5922C
enter a back-off mode where they drive the OUT pin
into high impedance for t
DCA
(2.8s). The DCA pin must
be connected high (MAX5922A) to activate the detec-
tion collision avoidance circuitry (if connected low, the
detection collision avoidance circuitry is disabled). The
MAX5922C has the detection collision avoidance cir-
cuitry permanently enabled (see the Typical
Application Circuit). After t
DCA
, the MAX5922A (with
DCA high) and the MAX5922C resume PD detection
operation. The MAX5922B has the detection collision
avoidance circuitry permanently disabled.
Detection Enable/Disable
The MAX5922A has the PD detection mode permanently
enabled. The MAX5922B/MAX5922C are equipped with
a DET_DIS pin, which provides the option of enabling or
disabling the power-device detection phase. With the
DET_DIS pin connected high, the PD detection and clas-
sification phases are disabled regardless of the status of
the class pin. With the DET_DIS pin connected low, the
PD detection is enabled.
Table 1. IEEE802.3af PD Specification
PARAMETER
VALID
PD DETECTION
SIGNATURE
NON-VALID
PD DETECTION
SIGNATURE
V/I (Slope)
19k& < R
PD
<
26.5k&
15k& > R
PD
or
R
RD
> 33k&
Input Capacitance
C
PD
< 0.6礔
C
PD
> 6礔
Offset Voltage
Up to 2.0V
Current Offset
Up to 12礎
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5923EUP+T | IC HOT-SWAP SWITCH +60V 20-TSSOP |
| MAX5926EEE+ | IC HOT-SWAP CONTROLLER 16QSOP-EP |
| MAX5929BEEG+ | IC HOT SWAP CTLR QUAD 24QSOP |
| MAX5930AEEG+ | IC HOT SWAP CTLR PWR SEQ 24QSOP |
| MAX5932ESA+T | IC HOT-SWAP CONTROLLER 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5922AEUI+ | 功能描述:熱插拔功率分布 48V Single-Port Network Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922AEUI+T | 功能描述:熱插拔功率分布 48V Single-Port Network Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922AEUI-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922BEUI | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5922BEUI+ | 功能描述:熱插拔功率分布 48V Single-Port Network Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。