參數資料
型號： MAX5893EGK+TD
廠商： Maxim Integrated Products
文件頁數： 18/32頁
文件大小： 0K
描述： IC DAC 12BIT DUAL 500MSPS 68-QFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
設置時間： 11ns
位數： 12
數據接口： 并聯
轉換器數目： 2
電壓電源： 模擬和數字
功率耗散（最大）： 511mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 68-VFQFN 裸露焊盤
供應商設備封裝： 68-QFN 裸露焊盤（10x10）
包裝： 帶卷 (TR)
輸出數目和類型： 2 電流，單極
采樣率（每秒）： 500M
Power-Down Mode
The MAX5893 features three power-saving modes.
Each DAC can be individually powered down through
bits 2 and 3 of address 00h. The interpolation filters can
also be powered down through bit 4 of address 00h,
preserving the output level of each DAC (the DACs
remain powered). Powering down both DACs will auto-
matically put the MAX5893 into full power-down, includ-
ing the interpolation filters.
Applications Information
Frequency Planning
System designers need to take the DAC into account
during frequency planning for high-performance appli-
cations. Proper frequency planning can ensure that
optimal system performance is achieved. The
MAX5893 is designed to deliver excellent dynamic per-
formance across wide bandwidths, as required for
communication systems. As with all DACs, some com-
binations of output frequency and update rate produce
better performance than others.
Harmonics are often folded down into the band of inter-
est. Specifically, if the DAC outputs a frequency close
to fS/N, the Mth harmonic of the output signal will be
aliased down to:
Thus, if N
≈ (M + 1), the Mth harmonic will be close to
the output frequency. SFDR performance of a current-
steering DAC is often dominated by third-order har-
monic distortion. If this is a concern, placing the output
signal at a different frequency other than fS/4 should be
considered.
Common to interpolating DACs are images near the
divided clocks. In a DAC configured for 4x interpolation
this applies to images around fS/4 and fS/2. In a DAC
configured for 8x interpolation this applies to images
around fS/8, fS/4, and fS/2. Most of these images are
not part of the in-band (0 to fDATA/2) SFDR specifica-
tion, though they are a consideration for out-of-band
(fDATA/2 - fDAC/2) SFDR and may depend on the rela-
tionship of the DATACLK to DAC update clock (see the
Data Clock section). When specifying the output recon-
struction filter for other than baseband signals, these
images should not be ignored.
Data Clock
The MAX5893 features synchronizers that allow for
arbitrary phase alignment between DATACLK and
CLKP/CLKN. The DATACLK causes internal switching
in the MAX5893 and the phase between DATACLK
(input mode) to CLKP/CLKN will influence the images
at DATACLK. Optimum image rejection is achieved
when DATACLK transitions are aligned with the falling
edge of CLKP. Figure 14 shows the image level near
DATACLK as a function of the DATACLK (input mode)
to CLKP/CLKN phase at 500Msps, 4x interpolation for a
10MHz, -6dBFS output signal.
Clock Interface
The MAX5893 features a flexible differential clock input
(CLKP, CLKN) with a separate supply (AVCLK) to
achieve optimum jitter performance. It uses an ultra-low
jitter clock to achieve the required noise density. Clock
jitter must be less than 0.5psRMS to meet the specified
noise density. For that reason, the CLKP/CLKN input
source must be designed carefully. The differential
clock (CLKN and CLKP) input can be driven from a sin-
gle-ended or a differential clock source. Differential
clock drive is required to achieve the best dynamic
performance from the DAC. For single-ended opera-
tion, drive CLKP with a low noise source and bypass
CLKN to GND with a 0.1F capacitor.
The CLKP and CLKN pins are internally biased to
AVCLK/2. This allows the user to AC-couple clock
ff
M f
f
NM
N
S
OUT
S
=×
=
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
______________________________________________________________________________________
25
Figure 14. Effect of CLKP/CLKN to DATACLK Phase on fS/4
Images
fS/4 IMAGES vs. CLKP/CLKN to DATACLK DELAY
fDATA = 125MWps, 4x INTERPOLATION
CLKP/CLKN DELAY (ns)
IMAGE
LEVEL
(dBc)
6.0
4.0
2.0
-100
-90
-80
-70
-60
-50
-110
0
8.0
fS/4 - fOUT
fOUT = 10MHz
AOUT = -6dBFS
fS/4 + fOUT
相關PDF資料
PDF描述
VI-25P-IW-S CONVERTER MOD DC/DC 13.8V 100W
MX7537JP+T IC DAC 12BIT DL MULT 28-PLCC
VI-25P-CU-F4 CONVERTER MOD DC/DC 13.8V 200W
VI-25P-CU-F2 CONVERTER MOD DC/DC 13.8V 200W
VI-25P-CU-F1 CONVERTER MOD DC/DC 13.8V 200W
相關代理商/技術參數
參數描述
MAX5893EVCMOD2 功能描述:數模轉換器- DAC Evaluation Kit for the MAX5893/MAX5894/MAX5895 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5893EVKIT 功能描述:數模轉換器- DAC Evaluation Kit for the MAX5893/MAX5894/MAX5895 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5894EGK+D 功能描述:數模轉換器- DAC 14-Bit 2Ch 500Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5894EGK+TD 功能描述:數模轉換器- DAC 14-Bit 2Ch 500Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5894EGK-D 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*