- 您現在的位置：買賣IC網 > PDF目錄383442 > MAX5820L (Maxim Integrated Products, Inc.) Dual D-type Positive-Edge-Triggered Flip-Flops With Preset And C 14-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX5820L |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual D-type Positive-Edge-Triggered Flip-Flops With Preset And C 14-CDIP -55 to 125 |
| 中文描述： | 雙路，8位，低功耗，2線，串行電壓輸出DAC |
| 文件頁數： | 8/13頁 |
| 文件大小： | 400K |
| 代理商： | MAX5820L |
M
The MAX5820 SDA and SCL drivers are open-drain out-
puts, requiring a pullup resistor to generate a logic high
voltage (see the
Typical Operating Circuit)
. Series
resistors R
S
are optional. These series resistors protect
the input stages of the MAX5820 from high-voltage
spikes on the bus lines, and minimize crosstalk and
undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see the
START
and STOP Conditions
section). Both SDA and SCL idle
high when the I
2
C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA, while SCL is high
(Figure 2). A START condition from the master signals
the beginning of a transmission to the MAX5820. The
master terminates transmission by issuing a not
acknowledge followed by a STOP condition (see the
Acknowledge Bit (ACK)
section)
.
The STOP condition
frees the bus. If a repeated START condition (Sr) is
generated instead of a STOP condition, the bus
remains active. When a STOP condition or incorrect
address is detected, the MAX5820 internally discon-
nects SCL from the serial interface until the next START
condition, minimizing digital noise and feedthrough.
Early STOP Conditions
The MAX5820 recognizes a STOP condition at any
point during transmission except if a STOP condition
occurs in the same high pulse as a START condition
(Figure 3). This condition is not a legal I
2
C format; at
least one clock pulse must separate any START and
STOP conditions.
Repeated START Conditions
A repeated START (S
r
) condition may indicate a
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. S
r
may also be used when the bus
master is writing to several I
2
C devices and does not
want to relinquish control of the bus. The MAX5820 seri-
al interface supports continuous write operations with or
without an S
r
condition separating them. Continuous
read operations require S
r
conditions because of the
change in direction of data flow.
Dual, 8-Bit, Low-Power, 2-Wire, Serial
Voltage-Output DAC
8
_______________________________________________________________________________________
POWER-DOWN
COMMAND BITS
PD1
PD0
MODE/FUNCTION
0
0
Power-up device. DAC output
restored to previous value.
0
1
Power-down mode 0. Power down
device with output floating.
1
0
Power-down mode 1. Power down
device with output terminated with
1k
to GND.
1
1
Power-down mode 2. Power down
device with output terminated with
100k
to GND.
Table 1. Power-Down Command Bits
SCL
SDA
STOP
CONDITION
START
CONDITION
REPEATED START CONDITION
START CONDITION
t
LOW
t
SU, DAT
t
SU, STA
t
SP
t
BUF
t
HD, STA
t
SU, STO
t
F
t
HD, STA
t
HIGH
t
HD, DAT
t
R
Figure 1. 2-Wire Serial-Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5820M | Dual D-type Positive-Edge-Triggered Flip-Flops With Preset And C 20-LCCC -55 to 125 |
| MAX5820 | Dual D-type Positive-Edge-Triggered Flip-Flops With Preset And C 14-CFP -55 to 125 |
| MAX5820LEUA | Dual, 8-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC |
| MAX5821MEUA | Dual, 10-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC |
| MAX5821 | Dual D-type Positive-Edge-Triggered Flip-Flops With Preset And C 14-CDIP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5820LEUA | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5820LEUA+ | 功能描述:數模轉換器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5820LEUA+T | 功能描述:數模轉換器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5820LEUA-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5820MEUA | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。