- 您現在的位置：買賣IC網 > PDF目錄383442 > MAX5622 (Maxim Integrated Products, Inc.) 16-Bit DACs with 16-Channel Sample-and-Hold Outputs PDF資料下載
參數資料
| 型號： | MAX5622 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 16-Bit DACs with 16-Channel Sample-and-Hold Outputs |
| 中文描述： | 16位DAC，帶有16通道采樣/保持輸出 |
| 文件頁數： | 10/16頁 |
| 文件大小： | 667K |
| 代理商： | MAX5622 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
M
16-Bit DACs with 32-Channel
Sample-and-Hold Outputs
10
______________________________________________________________________________________
voltage at the ground-sense input. With a 2.5V refer-
ence, the nominal endpoints are -4.0535V and
+9.0535V (Table 1). Note that these are
“
virtual
”
inter-
nal endpoint voltages and cannot be reached with all
combinations of negative and positive power-supply
voltages. The nominal, useable DAC endpoint codes
for the selected power supplies may be calculated as:
lower endpoint code = 32768 - ((2.5V - (V
SS
+0.75)) /
200μV) (result
≥
0)
upper endpoint code = 32768 + ((V
DD
- 2.4 - 2.5V) /
200μV) (result
≤
65535)
The resistive voltage-divider formed by the output resis-
tor (R
O
) and the load impedance (R
L
), scales the out-
put voltage. Determine V
OUT_
as follows:
Ground Sense
The MAX5631/MAX5632/MAX5633 include a ground-
sense input (GS), which allows the output voltages to
be referenced to a remote ground. The voltage at GS is
added to the output voltage with unity gain. Note that
the resulting output voltage must be within the valid
output voltage range set by the power supplies.
Output Clamp
The MAX5631/MAX5632/MAX5633 clamps the output
between two externally applied voltages. Internal
diodes at each channel restrict the output voltage to:
The clamping diodes allow the MAX5631/MAX5632/
MAX5633 to drive devices with restricted input ranges.
The diodes also allow the outputs to be clamped during
power-up or fault conditions. To disable output clamp-
ing, connect CH to V
DD
and CL to V
SS
, setting the
clamping voltages beyond the maximum output voltage
range.
Serial Interface
The MAX5631/MAX5632/MAX5633 are controlled by an
SPI, QSPI, and MICROWIRE-compatible 3-wire inter-
face. Serial data is clocked into the 24-bit shift register
in an MSB-first format, with the 16-bit DAC data pre-
ceding the 5-bit SRAM address, 2-bit control, and a fill
0 (Figure 4). The input word is framed by
CS
. The first
V
V
V
V
V
CH
OUT
CL
+
(
)
≥
≥
(
)
0 7
.
0 7
.
_
Scaling Factor
R
+
R
×
R
V
V
scaling factor
L
L
O
OUT
CHOLD
=
=
_
DATA
ADDRESS
CONTROL
D15 D14 D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01
MSB
D0
A4
A3
A2
A1
A0
C1
C0
0
LSB
Figure 4. Input Word Sequence
Figure 3. Analog Block Diagram
GS
DAC
DATA
CH
OUT_
GAIN
AND
OFFSET
C
HOLD
V
REF
R
O
ONE OF 32 SHA CHANNELS
16-BIT
DAC
R
L
CL
A
V
= 1
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5623 | 16-Bit DACs with 16-Channel Sample-and-Hold Outputs |
| MAX5633 | 16-Bit DACs with 32-Channel Sample-and-Hold Outputs |
| MAX563CPN | +3.3V-Powered, EIA/TIA-562 Dual Transceiver with Receivers Active in Shutdown |
| MAX563CWN | +3.3V-Powered, EIA/TIA-562 Dual Transceiver with Receivers Active in Shutdown |
| MAX5721EUA | 10-Bit, Low-Power, Dual, Voltage-Output DAC with Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5622AECB | 制造商:Maxim Integrated Products 功能描述: |
| MAX5622AETK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX5622UTK | 制造商:Maxim Integrated Products 功能描述:16-BIT DACS WITH 16-CHANNEL SAMPLE-AND-HOLD O - Rail/Tube |
| MAX5622UTK+ | 制造商:Maxim Integrated Products 功能描述:16-BIT DACS WITH 16-CHANNEL SAMPLE- - Rail/Tube |
| MAX5622UTK+T | 制造商:Maxim Integrated Products 功能描述:16-BIT DACS WITH 16-CHANNEL SAMPLE- - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。