- 您現在的位置：買賣IC網 > PDF目錄8538 > MAX5514ETC+ (Maxim Integrated Products)IC DAC 8BIT DUAL VOUT 12TQFN PDF資料下載
參數資料
| 型號： | MAX5514ETC+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8BIT DUAL VOUT 12TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 75 |
| 設置時間： | 660µs |
| 位數： | 8 |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 12-WQFN 裸露焊盤 |
| 供應商設備封裝： | 12-TQFN-EP（4x4） |
| 包裝： | 管件 |
| 輸出數目和類型： | 2 電壓，單極；2 電壓，雙極 |
| 采樣率（每秒）： | * |
Power Modes
The MAX5512–MAX5515 feature two power modes to
conserve power during idle periods. In normal opera-
tion, the device is fully operational. In shutdown mode,
the device is completely powered down, including the
internal voltage reference in the MAX5513/MAX5515.
The MAX5513/MAX5515 also offer a standby mode in
which all circuitry is powered down except the internal
voltage reference. Standby mode keeps the reference
powered up while the remaining circuitry is shut down,
allowing it to be used as a system reference. It also
helps reduce the wake-up delay by not requiring the ref-
erence to power up when returning to normal operation.
Shutdown Mode
The MAX5512–MAX5515 feature a software-programma-
ble shutdown mode that reduces the supply current and
the reference input current to 0.18A (max). Writing an
input control word with control bits C[3:0] = 1110 (Table
2) places the device in shutdown mode. In shutdown,
the MAX5512/MAX5514 reference input and DAC output
buffers go high impedance. Placing the MAX5513/
MAX5515 into shutdown turns off the internal reference
and the DAC output buffers go high impedance. The ser-
ial interface still remains active for all devices.
Table 2 shows several commands that bring the
MAX5512–MAX5515 back to normal operation. The
power-up time from shutdown is required before the
DAC outputs are valid.
Note: For the MAX5513/MAX5515, standby mode can-
not be entered directly from shutdown mode. The
device must be brought into normal operation first
before entering standby mode.
Standby Mode (MAX5513/MAX5515 Only)
The MAX5513/MAX5515 feature a software-program-
mable standby mode that reduces the typical supply
current to 3A (max). Standby mode powers down all
circuitry except the internal voltage reference. Place
the device in standby mode by writing an input control
word with control bits C[3:0] = 1100 (Table 2). The
internal reference and serial interface remain active
while the DAC output buffers go high impedance.
For the MAX5513/MAX5515, standby mode cannot be
entered directly from shutdown mode. The device must
be brought into normal operation first before entering
standby mode. To enter standby from shutdown, issue
the command to return to normal operation followed
immediately by the command to go into standby.
Table 2 shows several commands that bring the
MAX5513/MAX5515 back to normal operation. When
transitioning from standby mode to normal operation,
only the DAC power-up time is required before the DAC
outputs are valid.
Reference Input
The MAX5512/MAX5514 accept a reference with a volt-
age range extending from 0 to VDD. The output voltage
(VOUT) is represented by a digitally programmable volt-
age source as:
VOUT = (VREF x N / 256) x gain
where N is the numeric value of the DAC’s binary input
code (0 to 255), VREF is the reference voltage, gain is the
externally set voltage gain for the MAX5514, and gain is
one for the MAX5512.
In shutdown mode, the reference input enters a high-
impedance state with an input impedance of 2.5G (typ).
Reference Output
The MAX5513/MAX5515 internal voltage reference is
software configurable to one of four voltages. Upon
power-up, the default reference voltage is 1.214V.
Configure the reference voltage using D7 and D6 data
bits (Table 3) when the control bits are as follows C[3:0]
= 1100, 1101, or 1110 (Table 2). VDD must be kept at a
minimum of 200mV above VREF for proper operation.
MAX5512–MAX5515
Dual, Ultra-Low-Power,
8-Bit, Voltage-Output DACs
16
______________________________________________________________________________________
Table 3. Reference Output Voltage
Programming
D7
D6
REFERENCE VOLTAGE (V)
00
1.214
01
1.940
10
2.425
11
3.885
相關PDF資料 |
PDF描述 |
|---|---|
| 3-1877845-8 | PLUG 5POS 0 DEG BLK/YEL 4.0-5.2 |
| 3-1877845-2 | PLUG 5POS 0 DEG GRY/WH 4.0-5.2 |
| VE-JWW-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| MAX5514ETC+T | IC DAC 8BIT DUAL VOUT 12TQFN |
| VI-B0R-MX-S | CONVERTER MOD DC/DC 7.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5514ETC+ | 功能描述:數模轉換器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5514ETC+T | 功能描述:數模轉換器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5514ETC-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5515ETC | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5515ETC+ | 功能描述:數模轉換器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。