- 您現在的位置：買賣IC網 > PDF目錄385534 > MAX5486 (Maxim Integrated Products, Inc.) Stereo Volume Control with Pushbutton Interface PDF資料下載
參數資料
| 型號： | MAX5486 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Stereo Volume Control with Pushbutton Interface |
| 中文描述： | 立體聲音量控制，提供按鍵接口 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 232K |
| 代理商： | MAX5486 |
M
Stereo Volume Control with Pushbutton
Interface
_______________________________________________________________________________________
7
Pin Description
PIN
NAME
FUNCTION
1
V
LOGIC
Digital Logic Power Supply. Bypass V
LOGIC
to ground with a 0.1μF capacitor as close as possible to
the device.
2
DN
/
BALR
Active-Low Downward Volume/Balance Control. Press
DN
/
BALR
to decrease the volume in volume
mode and move balance to the right in balance mode.
DN
/
BALR
is internally pulled high with a
resistor to V
LOGIC
.
3
UP
/
BALL
Active-Low Upward Volume/Balance Control. Press
UP
/
BALL
to increase the volume in volume mode
and move balance to the left in balance mode.
UP
/
BALL
is internally pulled high with a resistor to
V
LOGIC
.
4
MUTE
Active-Low Mute Input. Pull
MUTE
low to toggle the wiper between the mute setting (see Table 1) and
the current setting.
MUTE
is internally pulled up to V
LOGIC
with a resistor.
5
MODE
Active-Low Volume/Balance Control Input. Each high-to-low transition on
MODE
toggles between the
volume and balance modes.
MODE
is pulled high internally with a resistor to V
LOGIC
. On power-up,
the MAX5486 is in volume control mode.
6
SHDN
Active-Low Shutdown Input. Drive
SHDN
low to place the device in shutdown mode. In shutdown
mode, the MAX5486 stores the last wiper settings. The wipers move to the L_ end of the resistor
string. Terminating the shutdown mode restores the wipers to the previous settings.
7
8
9
10
11
12
N.C.
HR
LR
WR
BIAS
BIASCAP
Internally connected. Leave unconnected.
Potentiometer R High Terminal
Potentiometer R Low Terminal
Potentiometer R Wiper Buffered Output
Midbias Voltage Output. V
BIAS
= (V
DD
+ V
SS
) / 2; connect a 100pF capacitor from BIAS to V
SS
.
Bias Generator Bypass. Connect a 1μF filter capacitor from BIASCAP to V
SS
.
Analog Power Supply. Bypass V
DD
to ground with a 0.1μF capacitor as close as possible to the
device.
13
V
DD
14
V
SS
Negative Power Supply. Bypass V
SS
to ground with a 0.1μF capacitor as close as possible to the
device. Connect to GND for single supply operation.
15
16
17
WL
LL
HL
Potentiometer L Wiper Buffered Output
Potentiometer L Low Terminal
Potentiometer L High Terminal
LED Indicator Open-Drain Output 0–LED Indicator Open-Drain Output 4. Connect a 1M
Ω
resistor
from LEDIND4 to V
LOGIC
to enable these LED inductor drivers. LEDIND0–LEDIND4 form a bar graph
indication of the current volume or balance. In volume mode, all LEDs off indicate mute and all LEDs
on indicate maximum volume. In balanced mode, LED2 on indicates centered or balanced. Connect
LEDIND0–LEDIND4 to GND when LED indicator drivers are not used.
18–22
LEDIND0–
LEDIND4
23
MODEIND
Active-Low Volume-Control/Balance-Control Mode-Indicator Open-Drain Output. Connect to an LED
through a resistor to V
LOGIC
. When the LED is on, the MAX5486 is in balance-control mode. When the
LED is off, the MAX5486 is in volume-control mode.
24
GND
Ground
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5494 | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5494ETE | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5495 | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5495ETE | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5496 | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5486EUG+ | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5486EUG+T | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE | 制造商:Maxim Integrated Products 功能描述:DUAL 256-TAP SPI 10K DIGITAL POTENTIOMETER - Rail/Tube |
| MAX5487ETE#G16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE#TG16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。