- 您現在的位置：買賣IC網 > PDF目錄9047 > MAX5477ETE#G16 (Maxim Integrated Products)IC POT DGTL DUAL 256-TAP 16-TQFN PDF資料下載
參數資料
| 型號： | MAX5477ETE#G16 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL DUAL 256-TAP 16-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 2 |
| 溫度系數： | 標準值 70 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN（3x3） |
| 包裝： | 管件 |
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
12
______________________________________________________________________________________
register with input shift register data and change the
wiper position. Use valid 3-byte I2C commands for
proper operation. This precautionary operation is nec-
essary only when transitioning from write protected
(WP = 1) to not write protected (WP = 0).
Serial Addressing
The MAX5477/MAX5478/MAX5479 operate as slave
devices that send and receive data through an I2C-/
SMBus-compatible 2-wire serial interface. The inter-
face uses a serial data access (SDA) line and a serial
clock line (SCL) to achieve bidirectional communication
between master(s) and slave(s). A master, typically a
microcontroller, initiates all data transfers to the
MAX5477/MAX5478/MAX5479, and generates the SCL
clock that synchronizes the data transfer (Figure 1).
The MAX5477/MAX5478/MAX5479 SDA line operates
as both an input and an open-drain output. The SDA
line requires a pullup resistor, typically 4.7k
. The
MAX5477/MAX5478/MAX5479 SCL line operates only
as an input. The SCL line requires a pullup resistor (typ-
ically 4.7k
) if there are multiple masters on the 2-wire
interface, or if the master in a single-master system has
an open-drain SCL output. SCL and SDA should not
exceed VDD in a mixed-voltage system, despite the
open-drain drivers.
Each transmission consists of a START (S) condition
(Figure 3) sent by a master, followed by the
MAX5477/MAX5478/MAX5479 7-bit slave address plus
the NOP/W bit (Figure 4), 1 command byte and 1 data
byte, and finally a STOP (P) condition (Figure 3).
START and STOP Conditions
Both SCL and SDA remain high when the interface is
not busy. A master controller signals the beginning of a
transmission with a START condition by transitioning
SDA from high to low while SCL is high. The master
controller issues a STOP condition by transitioning the
SDA from low to high while SCL is high, when it finishes
communicating with the slave. The bus is then free for
another transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on the SDA line must remain stable while SCL
is high (Figure 5).
Acknowledge
The acknowledge bit is a clocked 9th bit that the recipient
uses to handshake receipt of each byte of data (Figure
6). Thus, each byte transferred effectively requires 9 bits.
The master controller generates the 9th clock pulse, and
the recipient pulls down SDA during the acknowledge
clock pulse, so the SDA line remains stable low during
the high period of the clock pulse.
Slave Address
The MAX5477/MAX5478/MAX5479 have a 7-bit-long
slave address (Figure 4). The 8th bit following the 7-bit
slave address is the NOP/W bit. Set the NOP/W bit low for
a write command and high for a no-operation command.
The MAX5477/MAX5478/MAX5479 provide three
address inputs (A0, A1, and A2), allowing up to eight
devices to share a common bus (Table 1). The first 4
bits (MSBs) of the MAX5477/MAX5478/MAX5479 slave
addresses are always 0101. A2, A1, and A0 set the next
SDA
SCL
S
START
CONDITION
P
STOP
CONDITION
Figure 3. START and STOP Conditions
MSB
START
SCL
SDA
ACK
A0
A2
A1
101
0
LSB
NOP/W
Figure 4. Slave Address
SMBus is a trademark of Intel Corporation.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BT3-MY-F1 | CONVERTER MOD DC/DC 24V 50W |
| VI-B5Z-MY-F4 | CONVERTER MOD DC/DC 2V 20W |
| ICS91857AGLF | IC CLOCK DRIVER SSTL_2 48-TSSOP |
| DS1869S-C04+ | IC RHEOSTAT DALLAST 3V 10K 8SOIC |
| VI-B5Z-MY-F3 | CONVERTER MOD DC/DC 2V 20W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5477EUD | 制造商:Maxim Integrated Products 功能描述:DUAL, 256-TAP, NONVOLATILE, I2C-INTERFACE, DI - Rail/Tube |
| MAX5477EUD+ | 功能描述:數字電位計 IC Dual 256-Tap NV I2C-Interface RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5477EUD+T | 功能描述:數字電位計 IC Dual 256-Tap NV I2C-Interface RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5477EUD-T | 制造商:Maxim Integrated Products 功能描述:DUAL, 256-TAP, NONVOLATILE, I2C-INTERFACE, DI - Tape and Reel |
| MAX5478ETD | 制造商:Maxim Integrated Products 功能描述:DUAL, 256-TAP, NONVOLATILE, I2C-INTERFACE, DI - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。