參數資料
型號: MAX494
廠商: Maxim Integrated Products, Inc.
英文描述: Quad, Micropower, Single-Supply Rail-to-Rail Op Amps(輸入失調電壓500μV,單電源滿量程運放)
中文描述: 單/雙/四路、微功耗、單電源、滿擺幅運算放大器
文件頁數: 11/16頁
文件大?。?/td> 224K
代理商: MAX494
M
S ingle/Dual/Quad, Mic ropower,
S ingle-S upply Rail-to-Rail Op Amps
______________________________________________________________________________________
11
the op amp in an inverting configuration (Figure 3a);
connect resistor R3 between the noninverting input and
the input signal when using the op amp in a noninvert-
ing configuration (Figure 3b). Select R3 to equal the
parallel combination of R1 and R2. High source resis-
tances will degrade noise performance, due to the ther-
mal noise of the resistor and the input current noise
(which is multiplied by the source resistance).
Output Loading and S tability
Even with their low quiescent current of less than
150μA per op amp, the MAX492/MAX494/MAX495 are
well suited for driving loads up to 1k
while maintaining
DC accuracy. Stability while driving heavy capacitive
loads is another key advantage over comparable
CMOS rail-to-rail op amps.
In op amp circuits, driving large capacitive loads
increases the likelihood of oscillation. This is especially
true for circuits with high loop gains, such as a unity-
gain voltage follower. The output impedance and a
capacitive load form an RC network that adds a pole to
the loop response and induces phase lag. If the pole
frequency is low enough—as when driving a large
capacitive load—the circuit phase margin is degraded,
leading to either an under-damped pulse response or
oscillation.
The MAX492/MAX494/MAX495 can drive capacitive
loads in excess of 1000pF under certain conditions
(Figure 4). When driving capacitive loads, the greatest
potential for instability occurs when the op amp is
sourcing approximately 100μA. Even in this case, sta-
R1
V
OUT
R3 = R2
II
R1
R3
V
IN
R2
MAX49_
Figure 3a. Reducing Offset Error Due to Bias Current:
Inverting Configuration
R3
V
OUT
R3 = R2
II
R1
V
IN
R1
R2
MAX49_
Figure 3b. Reducing Offset Error Due to Bias Current:
Noninverting Configuration
V
50mV/div
V
50mV/div
10,000
100
1
10
100
M
RESISTIVE LOAD (k
)
C
1000
UNSTABLE REGION
V
CC
= +5V
V
OUT
= V
CC
/2
R
L
TO V
EE
A
V
= +1
Figure 4. Capacitive-Load Stable Region Sourcing Current
Figure 5. MAX492 Voltage Follower with 1000pF Load
(R
L
=
)
相關PDF資料
PDF描述
MAX5003 High-Voltage PWM Power-Supply Controller
MAX5003CEE High-Voltage PWM Power-Supply Controller
MAX5003CSE High-Voltage PWM Power-Supply Controller
MAX5003EEE High-Voltage PWM Power-Supply Controller
MAX5003ESE RES 240-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA
相關代理商/技術參數
參數描述
MAX4940ACTN+ 功能描述:功率驅動器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4940ACTN+T 功能描述:功率驅動器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4940BETN+ 功能描述:功率驅動器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4940BETN+T 功能描述:功率驅動器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MAX4940CTN+ 功能描述:功率驅動器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube