- 您現在的位置：買賣IC網 > PDF目錄296463 > MAX4833EUT18C (MAXIM INTEGRATED PRODUCTS INC) 1.8 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, PDSO6 PDF資料下載
參數資料
| 型號： | MAX4833EUT18C |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 固定正電壓單路輸出LDO穩壓器 |
| 英文描述： | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, PDSO6 |
| 封裝： | MO-178AB, SOT-23, 6 PIN |
| 文件頁數： | 15/15頁 |
| 文件大小： | 516K |
| 代理商： | MAX4833EUT18C |
Shutdown Discharge (MAX4833)
OUT discharges through a 900
internal resistor during
shutdown mode.
Reverse OUT to IN Current
When the output voltage is greater than the input volt-
age, the internal pass transistor turns off. To avoid
reverse-charging the input source, the current at IN is
guaranteed to be below 3A when VOUT
≥ VIN.
Current Limit
The MAX4832/MAX4833 include an accurate internal
current-limiting circuit. OUT can be shorted to ground
indefinitely without damaging the part.
The MAX4832 latches off if the load current exceeds the
current limit for more than the blanking time (see the
FLAG Output section). During soft-start, the device does
not latch off to an overload condition. During an overload
condition, the MAX4833 holds the current at current limit
until the thermal limit is reached. Once the junction tem-
perature reaches +165°C, thermal shutdown occurs.
Thermal Shutdown
When the junction temperature (TJ) exceeds +165°C,
the LDO’s pass transistor turns off allowing the junction
to cool. The LDO’s pass transistor turns on again after
the IC’s junction temperature cools by 15°C, resulting in
a pulsed output during continuous thermal-overload
conditions.
Soft-Start
During power-up, the soft-start ensures that the output
ramps up slowly reducing inrush current peaks. See
the soft-start response time plots in the Typical
Operating Characteristics. The soft-start time (tSS) is
given by the following equation:
tSS = CSS (ms)
where CSS is in nF.
A soft-start capacitor (CSS) of 10nF gives a 10ms tSS. A
1ms minimum soft-start time is fixed internally to ensure
that the output rises slowly even without any external
capacitor at SS pin to ground. The device is in soft-start
mode when either the voltage at IN or SHDN is cycled
high to low to high.
Applications Information
Capacitor Selection and Regulator
Stability
For stable operation over the full temperature range and
with load currents up to 100mA, use a 3.3F (min)
ceramic output capacitor with an ESR <0.2
. To reduce
noise and improve load transient response, stability, and
power-supply rejection, use larger output capacitor
values such as 10F (note that some ceramic capacitors
exhibit large capacitance and ESR variation with temper-
ature). X7R capacitors provide good performance over
the -40°C to +85°C operating temperature range.
To improve power-supply rejection and transient
response, use a 0.1F capacitor between IN and GND.
The MAX4832/MAX4833 remain stable with purely
resistive loads or current loads up to 100mA.
15kV Operational ESD Protection
A 3.3F or higher value ceramic capacitor from OUT to
GND provides a 15kV (Human Body Model) protection
at OUT. The ESR value of the capacitor should be less
than 0.2
.
Reset Transient Immunity
The reset circuit is relatively immune to short duration,
falling VOUT transients. The Typical Operating
Characteristics show a graph of the Maximum Transient
Duration vs. Reset Threshold Overdrive for which reset is
not asserted. The graph was produced using falling VOUT
transients starting at VOUT and ending below the reset
threshold by the magnitude indicated (reset threshold
overdrive). The graph shows the maximum pulse width
that a falling VOUT transient can typically have without
triggering the reset pulse. As the amplitude of the tran-
sient increases (i.e., goes further below the reset thresh-
old), the maximum allowable pulse width decreases.
Typically, a VOUT transient that goes only 10mV below the
reset threshold and lasts up to 54s does not trigger a
reset pulse.
Layout
When using the TDFN package, connect its exposed
paddle to GND to provide a low thermal resistance
path for heat transfer from the IC junction to the printed
circuit board.
MAX4832/MAX4833
100mA LDO Linear Regulators with
Current-Limiting Switch
_______________________________________________________________________________________
9
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4833EUT18BD4 | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, PDSO6 |
| MAX4833EUT18BD3 | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, PDSO6 |
| MAX4833EUT18BD2 | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, PDSO6 |
| MAX4833EUT18BD1 | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, PDSO6 |
| MAX4833ETT33C | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.13 V DROPOUT, DSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4833EUT25BD3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4833EUT28D3-T | 功能描述:低壓差穩壓器 - LDO 100mA LDO Linear Regulators with Current-Limiting Switch RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX4833EUT30BD3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4833EUT33BD3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4833EUT33BD3-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。