參數資料
型號: MAX4793EUK+T
廠商: Maxim Integrated Products
文件頁數: 10/11頁
文件大?。?/td> 0K
描述: IC ANALOG SWITCH 1X1 SOT23-5
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
功能: 開關
電路: 1 x 1:1
導通狀態電阻: 400 毫歐
電壓電源: 單電源
電壓 - 電源,單路/雙路(±): 2.3 V ~ 5.5 V
電流 - 電源: 80µA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: SC-74A,SOT-753
供應商設備封裝: SOT-23-5
包裝: 標準包裝
產品目錄頁面: 1421 (CN2011-ZH PDF)
其它名稱: MAX4793EUK+TDKR
MAX4789–MAX4794
Applications Information
Input Capacitor
To limit the input voltage drop during momentary output
short-circuit conditions, connect a capacitor from IN to
GND. A 0.1F ceramic capacitor is adequate for most
applications; however, higher capacitor values further
reduce the voltage drop at the input and are recom-
mended for lower voltage applications.
Output Capacitance
Connect a 0.1F capacitor from OUT to GND. This
capacitor helps prevent inductive parasitics from
pulling OUT negative during turn-off, thus preventing
the MAX4789–MAX4794 from tripping erroneously. If
the load capacitance is too large, then current may not
have enough time to charge the capacitance and the
device assumes that there is a faulty load condition.
The maximum capacitive load value that can be driven
from OUT is obtained by the following formula:
Layout and Thermal Dissipation
To optimize the switch response time to output short-
circuit conditions, it is very important to keep all traces
as short as possible to reduce the effect of undesirable
parasitic inductance. Place input and output capacitors
as close as possible to the device (no more than 5mm).
IN and OUT pins must be connected with short traces
to the power bus.
During normal operation, the power dissipation is small
and the package temperature change is minimal. If the
output is continuously shorted to ground at the maxi-
mum supply voltage, the operation of the switches with
the autoretry option does not cause problems because
the total power dissipated during the short is scaled by
the duty cycle:
where VIN = 5.5V, IOUT = 450mA, tBLANK = 14ms, and
tRETRY = 98ms.
Attention must be given to the MAX4789, MAX4791,
and MAX4793 where the latch-off condition must be
manually reset by toggling ON from high to low. If the
latch-off time duration is not sufficiently high, it is possi-
ble for the device to reach the thermal-shutdown
threshold and never be able to turn the device on until it
cools down.
Chip Information
PROCESS: BiCMOS
P
VI
t
tt
mW
MAX
IN MAX
OUT MAX
BLANK
RETRY
BLANK
=
××
+
=
__
302
C
It
V
MAX
FWD MIN
BLANK MIN
IN
<
×
__
200mA/250mA/300mA Current-Limit Switches
8
_______________________________________________________________________________________
LOAD
CURRENT
SWITCH
STATUS
ON PIN
VOLTAGE
tBLANK
OFF
ON
(a)
(b)
UVLO
LOAD
CURRENT
SWITCH
STATUS
IN PIN
VOLTAGE
OFF
ON
tBLANK
FLAG PIN
STATUS
FLAG PIN
STATUS
Figure 3. MAX4789/MAX4791/MAX4793 Latch-Off Fault
Blanking
相關PDF資料
PDF描述
GRM219R71E684KA88D CAP CER 0.68UF 25V 10% X7R 0805
VI-2NR-CV-F3 CONVERTER MOD DC/DC 7.5V 150W
DSPIC33FJ16GS502-E/SO IC DSPIC MCU/DSP 16K 28-SOIC
PIC18F2455T-I/SO IC PIC MCU FLASH 12KX16 28SOIC
VI-2NR-CV-F1 CONVERTER MOD DC/DC 7.5V 150W
相關代理商/技術參數
參數描述
MAX4793EUS 制造商:Maxim Integrated Products 功能描述:200MA/250MA/300MA CURRENT-LIMIT SWI - Cut Tape Product
MAX4793EUS+T 功能描述:電源開關 IC - 配電 200/250/300mA Crnt Limit Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MAX4793EUS-T 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MAX4794ETT 制造商:Maxim Integrated Products 功能描述:200MA/250MA/300MA CURRENT-LIMIT SWITCHES - Rail/Tube
MAX4794ETT+ 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: