- 您現在的位置：買賣IC網 > PDF目錄11155 > MAX4772ETT+T (Maxim Integrated Products)IC SWITCH 1X1 6TDFN PDF資料下載
參數資料
| 型號： | MAX4772ETT+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH 1X1 6TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 開關 |
| 電路： | 1 x 1:1 |
| 導通狀態電阻： | 360 毫歐 |
| 電流 - 電源： | 125µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-WDFN 裸露焊盤 |
| 供應商設備封裝： | 6-TDFN 裸露焊盤（3x3） |
| 包裝： | 帶卷 (TR) |
MAX4772/MAX4773
200mA/500mA Selectable
Current-Limit Switches
_______________________________________________________________________________________
9
reduce the voltage drop at the input and are recom-
mended for lower voltage applications.
Output Capacitance
Connect a 0.1F capacitor from OUT to GND. This
capacitor helps prevent inductive parasitics from
pulling OUT negative during turn-off, thus preventing
the MAX4772/MAX4773 from tripping erroneously. If the
load capacitance is too large, then current may not
have enough time to charge the capacitance and the
device assumes that there is a faulty load condition.
The maximum capacitive load value that can be driven
from OUT is obtained by the following formula:
Layout and Thermal Dissipation
To optimize the switch response time to output short-
circuit conditions, it is very important to keep all traces
as short as possible to reduce the effect of undesirable
parasitic inductance. Place input and output capacitors
as close as possible to the device (no more than 5mm).
IN and OUT pins must be connected with short traces
to the power bus.
During normal operation, the power dissipation is small
and the package temperature change is minimal. If the
output is continuously shorted to ground at the maxi-
mum supply voltage, the operation of the switches with
the autoretry option does not cause problems because
the total power dissipated during the short is scaled by
the duty cycle:
where VIN = 4.5V, IOUT = 750mA, tBLANK = 14ms, and
tRETRY = 210ms.
Attention must be given to the MAX4772 where the
latch-off condition must be manually reset by toggling
ON from high to low. If the latch-off time duration is not
sufficiently high, it is possible for the device to reach
the thermal-shutdown threshold and never be able to
turn the device on until it cools down.
Chip Information
TRANSISTOR COUNT: 2539
PROCESS: BiCMOS
P
VI
t
tt
mW
MAX
IN MAX
OUT MAX
BLANK
RETRY
BLANK
=
××
+
=
__
211
C
It
V
MAX
FWD MIN
BLANK MIN
IN
<
×
__
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4932EBC+T | IC MULTIPLEXER DUAL 3X1 12UCSP |
| MAX4618CPE+ | IC MULTIPLEXER DUAL 4X1 16DIP |
| MAX4066CEE+T | IC SWITCH QUAD SPST 16QSOP |
| C8051F330-GMR | IC 8051 MCU 8K FLASH 20MLP |
| MAX4625EUT-T | IC SWITCH SPDT SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4772EUT | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
| MAX4772EUT+ | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
| MAX4772EUT+T | 功能描述:電源開關 IC - 配電 200mA/500mA Select Current-Limit Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MAX4772EUT-T | 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MAX4773ETT-T | 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。