參數資料
型號: MAX4733EBL
廠商: Maxim Integrated Products, Inc.
英文描述: 50ヘ, Dual SPST Analog Switches in UCSP
中文描述: 50ヘ,雙路SPST模擬開關的UCSP封裝
文件頁數: 8/14頁
文件大小: 380K
代理商: MAX4733EBL
M
Analog Signal Levels
Analog signals that range over the entire supply voltage
(GND to V+) pass with very little change in R
ON
(see
Typical Operating Characteristics
). The bidirectional
switches allow NO_, NC_, and COM_ connections to be
used as either inputs or outputs.
Power-Supply Sequencing and
Overvoltage Protection
CAUTION: Do not exceed the absolute maximum
ratings. Stresses beyond the listed ratings can
cause permanent damage to the devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+ before applying
analog signals, especially if the analog signal is not
current limited. If this sequencing is not possible, and if
the analog inputs are not current limited to < 20mA,
add a small-signal diode, D1, as shown in Figure 1. If
the analog signal can dip below GND, add D2. Adding
protection diodes reduces the analog signal range to a
diode drop (about 0.7V) below V+ (for D1), and to a
diode drop above ground (for D2). Leakage is unaffect-
ed by adding the diodes. On-resistance increases
slightly at low supply voltages. Maximum supply volt-
age (V+) must not exceed +11V.
Adding protection diodes causes the logic thresholds to
be shifted relative to the power-supply rails. The most
significant shift occurs when using low supply voltages
(+5V or less). With a +5V supply, TTL compatibility is not
guaranteed when protection diodes are added. Driving
IN1 and IN2 all the way to the supply rails (i.e., to a
diode drop higher than the V+ pin, or to a diode drop
lower than the GND pin) is always acceptable.
Protection diodes D1 and D2 also protect against some
overvoltage situations. Using the circuit in Figure 1, no
damage results if the supply voltage is below the
absolute maximum rating (+12V) and if a fault voltage
up to the absolute maximum rating (V+ + 0.3V) is
applied to an analog signal terminal.
UCSP Applications Information
For the latest application details on USCP construction,
dimensions, tape carrier information, printed circuit
board techniques, bump-pad layout, and recommend-
ed reflow temperature profile as well as the latest infor-
mation on reliability testing results, go to the Maxim
web site at www.maxim-ic.com/ucsp to find the
Application Note:
UCSP—A Wafer-Level Chip-Scale
Package
.
50
,
Dual SPST Analog Switches in UCSP
8
_______________________________________________________________________________________
MAX4731
MAX4732
MAX4733
NO_
COM_
GND
V+
*INTERNAL PROTECTION DIODES.
D2
D1
EXTERNAL BLOCKING DIODE
EXTERNAL BLOCKING DIODE
GND
V+
*
*
*
*
Figure 1. Overvoltage Protection Using External Blocking Diodes
Test Circuits/Timing Diagrams
相關PDF資料
PDF描述
MAX4733ETA 50ヘ, Dual SPST Analog Switches in UCSP
MAX4741EUA 0.8з, Low-Voltage, Single-Supply Dual SPST Analog Switches
MAX4741EKA 0.8з, Low-Voltage, Single-Supply Dual SPST Analog Switches
MAX4741 0.8Ω,low-voltage,single-supply dual SPST analog switches
MAX4743EUA 3.3V CAN Transceiver with Sleep Mode 8-SOIC -40 to 85
相關代理商/技術參數
參數描述
MAX4733EBL+ 制造商:Maxim Integrated Products 功能描述:ANALOG SWITCH, DUAL, SPST, 1 NC SWITCH, 9 PIN PLASTIC BGA - Rail/Tube
MAX4733EBL+T 制造商:Maxim Integrated Products 功能描述:ANLG SW DUAL SPST 11V 9UCSP - Rail/Tube
MAX4733EBL-T 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX4733ETA+ 制造商:Maxim Integrated Products 功能描述:50OHM DUAL SPST ANALOG SWITCHES IN - Rail/Tube
MAX4733ETA+T 功能描述:模擬開關 IC 50Ohm Dual SPST Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16