- 您現在的位置：買賣IC網 > PDF目錄383418 > MAX4670 (Maxim Integrated Products, Inc.) Integrated T1/E1/J1 Short-Haul and Long-Haul Protection Switch PDF資料下載
參數資料
| 型號： | MAX4670 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Integrated T1/E1/J1 Short-Haul and Long-Haul Protection Switch |
| 中文描述： | 集成T1/E1/J1短程、長程保護開關 |
| 文件頁數： | 8/20頁 |
| 文件大小： | 1136K |
| 代理商： | MAX4670 |
M
Detailed Description
The MAX4670 is a quad-DPDT/octal-SPDT analog switch
optimized for T1/E1/J1 line-card redundancy protection
applications. This analog switch is configurable as two
differential transmitter and receiver pairs utilized in
T1/E1/J1 redundancy architecture.
The MAX4670 has four low 0.7
on-resistance switches
with 60pF and 40pF on- and off-capacitances, respec-
tively, for interfacing to the LIU transmitter inputs. The
MAX4670 also includes four 5
on-resistance switches
with low 24pF and 12pF on- and off-capacitances,
respectively, for interfacing to the LIU receiver inputs.
The MAX4670 replaces two diode arrays or two tran-
sient voltage suppressors and four dual-SPDT relays,
significantly reducing board space and simplifying PC
board routing. The MAX4670 pinouts are targeted for
T1/E1/J1 applications, resulting in a simplified layout
when interfacing with standard line transformers and
LIUs. Figure 1 is the functional diagram.
Logic Inputs (IN_,
SWITCH
)
The MAX4670 four logic inputs (IN_) control the switches
in pairs and contain a global logic input (
SWITCH
) that
connects all COMs to their respective NO_ inputs.
SWITCH
overrides all IN_ inputs when asserted low, thus
connecting all NO_ to COM_ outputs (transmitter/receiver
pairs to the protection bus). When
SWITCH
asserts high,
IN_ controls the switch pairs. See Table 1.
Surge Protection
The MAX4670 includes chip-side, surge-protection capa-
bility for short-haul intrabuilding applications. The low-
capacitance diodes suppress surge residuals from the
primary, line-side protection devices. It is assumed that
adequate primary protection is included on the line die of
the transformer, as represented in Figures 7
–
10. Table 2
lists the applicable surge protection setups for E1
interfaces. The MAX4670 surge test was performed per
IEC 61000-4-5 Class 2 specifications and passed at ±1kV
with only an in-line transformer and primary surge sup-
pressor. The transformer was a Halo TG83-1505NX trans-
former and the surge suppressor was a Teccor P0640SC.
Applications Information
Redundancy Architecture
Figures 7 through 10 illustrate the MAX4670 used in two
different redundancy architectures. There is one back-
up card for up to N line cards in the system (in this
example, N = 3). In the event one of the line cards fails
(memory failure, power supply went down, etc.), a sys-
tem supervisory card issues a command to the switch-
es to reroute the traffic to and from the problem line
card to the backup line card.
Integrated T1/E1/J1 Short-Haul and
Long-Haul Protection Switch
8
_______________________________________________________________________________________
PIN
22
NAME
NC4
FUNCTION
Normally Closed Terminal 4. Transmitter 1 differential terminal. Connect NC4 to LIU receiver.
23
NO3
Normally Open Terminal 3. Transmitter 1 differential protection terminal. Connect NO3 to the
protection bus.
24
NC3
Normally Closed Terminal 3. Transmitter 1 differential terminal. Connect NC3 to LIU receiver.
25
NO2
N or m al y Op en Ter m nal 2. Recei ver 2 differential protection terminal. C onnect NO2 to the
p otecti on b us.
26
NC2
Normally Closed Terminal 2. Receiver 1 differential terminal. Connect NC2 to LIU receiver.
27
NO1
N or m al y Op en Ter m nal 1. Recei ver 1 differential protection terminal. C onnect NO1 to the
p otecti on b us.
28
NC1
Normally Closed Terminal 1. Receiver 1 differential terminal. Connect NC1 to LIU receiver.
29
COM1
Common Terminal 1. Receiver 1 positive differential terminal. Connect COM1 to the receive
interface transformer.
30
COM2
Common Terminal 2. Receiver 1 negative differential terminal. Connect COM2 to the receive
interface transformer.
31
INA
Receiver 1 Logic Control. Drive INA low to connect receiver 1 to the LIU. INA logic is ignored
when
SWITCH
asserts low.
EP
EP
Exposed Paddle. Connect EP to GND or leave unconnected.
Pin Description (continued)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4670ETJ | Integrated T1/E1/J1 Short-Haul and Long-Haul Protection Switch |
| MAX4688 | 2.5?, Low-Voltage, SPST/SPDT Analog Switches in UCSP Package |
| MAX4688EBT-T | 2.5?, Low-Voltage, SPST/SPDT Analog Switches in UCSP Package |
| MAX4686EBT-T | 2.5?, Low-Voltage, SPST/SPDT Analog Switches in UCSP Package |
| MAX4686 | 2.5?, Low-Voltage, SPST/SPDT Analog Switches in UCSP Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4670ETJ | 功能描述:通信集成電路 - 若干 RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX4670ETJ+ | 功能描述:模擬開關 IC Integrated T1/E1/J1 rotection Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4670ETJ+T | 功能描述:模擬開關 IC Integrated T1/E1/J1 rotection Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4670ETJ-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4670EUU | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。