- 您現在的位置：買賣IC網 > PDF目錄383417 > MAX4649EKA (Maxim Integrated Products, Inc.) PLASTIC ENCAPSULATED DEVICES PDF資料下載
參數資料
| 型號： | MAX4649EKA |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | PLASTIC ENCAPSULATED DEVICES |
| 中文描述： | 塑封器件 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 62K |
| 代理商： | MAX4649EKA |
V. Quality Assurance Information
A. Quality Assurance Contacts: : Jim Pedicord (Reliability Lab Manager)
Bryan Preeshl (Executive Director)
Kenneth Huening (Vice President)
B. Outgoing Inspection Level: 0.1% for all electrical parameters guaranteed by the Datasheet.
0.1% For all Visual Defects.
C. Observed Outgoing Defect Rate: < 100 ppm
D. Sampling Plan: Mil-Std-105D
VI. Reliability Evaluation
A. Accelerated Life Test
The results of the 135
°
C biased (static) life test are shown in
Table 1
. Using these results, the Failure Rate
(
λ
) is calculated as follows:
λ
= 1 = 1.83 (Chi square value for MTTF upper limit)
MTTF
192 x 4389 x 80 x 2
Temperature Acceleration factor assuming an activation energy of 0.8eV
λ
= 13.57 x 10
-9
λ
= 13.57 F.I.T. (60% confidence level @ 25
°
C)
This low failure rate represents data collected from Maxim’s reliability monitor program. In addition to
routine production Burn-In, Maxim pulls a sample from every fabrication process three times per week and subjects
it to an extended Burn-In prior to shipment to ensure its reliability. The reliability control level for each lot to be
shipped as standard product is 59 F.I.T. at a 60% confidence level, which equates to 3 failures in an 80 piece
sample. Maxim performs failure analysis on any lot that exceeds this reliability control level. Attached Burn-In
Schematic (Spec. # 06-5703) shows the static Burn-In circuit. Maxim also performs quarterly 1000 hour life test
monitors. This data is published in the Product Reliability Report (
RR-1I
).
B. Moisture Resistance Tests
Maxim pulls pressure pot samples from every assembly process three times per week. Each lot sample
must meet an LTPD = 20 or less before shipment as standard product. Additionally, the industry standard
85
°
C/85%RH testing is done per generic device/package family once a quarter.
C. E.S.D. and Latch-Up Testing
The AH58 die type has been found to have all pins able to withstand a transient pulse of
±
400V, per Mil-
Std-883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device
withstands a current of
±
100mA and/or
±
20V.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4649 | 1.75-W 3-Channel Stereo Audio Power Amplifier 24-HTSSOP |
| MAX4651EGE | Low-Voltage, 4з, Quad, SPST, CMOS Analog Switches |
| MAX4651EGP | Low-Voltage, 4з, Quad, SPST, CMOS Analog Switches |
| MAX4652EGE | Low-Voltage, 4з, Quad, SPST, CMOS Analog Switches |
| MAX4652EGP | Low-Voltage, 4з, Quad, SPST, CMOS Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4649EKA+ | 制造商:Maxim Integrated Products 功能描述:45 OHM SPDT ANALOG SWITCH IN SOT23-8 制造商:Maxim Integrated Products 功能描述:ANLG SW SGL SPDT 20V/36V 8PIN SOT-23 - Bulk |
| MAX4649EKA+T | 功能描述:模擬開關 IC 45Ohm SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4649EKA+TG0N | 功能描述:模擬開關 IC 45 Ohm SPDT Analog Switch in SOT23-8 RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4649EKA-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX464C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。