The MAX4548 use" />
參數資料
型號: MAX4549EAX+T
廠商: Maxim Integrated Products
文件頁數: 7/20頁
文件大?。?/td> 0K
描述: IC AUD/VIDCROSSPOINT SWIT 36SSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1,000
功能: 音頻/視頻交叉點開關
電路: 3 x 3:2
導通狀態電阻: 35 歐姆
電壓電源: 單電源
電壓 - 電源,單路/雙路(±): 2.7 V ~ 5.5 V
電流 - 電源: 6µA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 36-BSOP(0.295",7.50mm 寬)
供應商設備封裝: 36-SSOP
包裝: 帶卷 (TR)
the same configuration. Any block that is not selected
in the command byte remains unchanged.
2-Wire Serial Interface
The MAX4548 uses a 2-wire I2C-compatible serial inter-
face. The COM_ _ registers and the Clickless Mode
register use the “WriteByte” protocol, which consists of
an address byte, followed by a command byte, fol-
lowed by a data byte (Table 5). The Bias register uses
the “WriteWord” protocol, which consists of an address
byte, followed by a command byte, followed by a data
word (Table 6).
To address a given chip, the A0 and A1 bits in the
address byte must duplicate the values present at the
A0 and A1 pins of that chip. The rest of the address bits
must match those shown in Tables 5 and 6. The com-
mand and data-byte details are described in the
Command-Byte and Data-Byte Programming section.
The 2-wire serial interface requires only two I/O lines of
a standard microprocessor port. Figures 3, 4, and 5
detail the timing diagram for signals on the 2-wire bus,
while Tables 5 and 6 detail the format of the signals.
The MAX4548 is a receive-only device and must be
controlled by the bus master device. A bus master
device communicates by transmitting the address byte
of the slave device over the bus and then transmitting
the desired information. Each transmission consists of
a start condition, a command byte, a data byte or word,
and finally a stop condition. The slave device acknowl-
edges the recognition of its address by pulling the SDA
line low for one clock period after the address byte is
transmitted. The slave device also issues a similar
acknowledgment after the command byte and again
after each data byte.
Start and Stop Conditions
The bus master signals the beginning of a transmission
with a start condition by transitioning SDA from high to
low while SCL is high. When the master has finished
communicating with the slave, it issues a stop condition
by transitioning SDA from low to high while SCL is high.
The bus is then free for another transmission.
MAX4548/MAX4549
Serially Controlled, Triple 3x2 Audio/Video
Crosspoint Switches
______________________________________________________________________________________
15
CS
SCLK
DIN
COMMAND BYTE
DATA BYTE
24
1
C7
D0
C0
D15
Figure 6. 3-Wire Serial-Interface Communication
CS
SCLK
DIN
DOUT
tCSH
tCSS
tCL
tDS
tDH
tDV
tCH
tDO
tTR
tCSH
Figure 7. 3-Wire Serial-Interface Timing Details
相關PDF資料
PDF描述
MAX4550CWI+T IC CROSSPOINT SWITCH DUAL 28SOIC
DG413ETE+T IC SWITCH QUAD SPST 16TQFN
DG412EUE+T IC SWITCH QUAD SPST 16TSSOP
EFM32LG295F64 IC MCU 32BIT 64KB FLASH BGA120
R5F100LEAFC#V0 MCU 16BIT 64KB FLASH 64TQFP
相關代理商/技術參數
參數描述
MAX454CPD 功能描述:視頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX454CPD+ 功能描述:視頻放大器 50MHz Video Amp & MUX Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX454CSD 功能描述:視頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX454CSD+ 功能描述:視頻放大器 50MHz Video Amp & MUX Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX454CSD+T 功能描述:視頻放大器 50MHz Video Amp & MUX Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel