- 您現在的位置：買賣IC網 > PDF目錄11137 > MAX4527CSA+T (Maxim Integrated Products)IC SWITCH DUAL SPDT 8SOIC PDF資料下載
參數資料
| 型號： | MAX4527CSA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/12頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SPDT 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 175 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 36 V，±4.5 V ~ 18 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
Power-Supply Considerations
Overview
The MAX4526/MAX4527 construction is typical of most
CMOS analog switches. It has three supply pins: V+, V-,
and GND. V+ and V- drive the internal CMOS switches
and set the analog-voltage limits on any switch.
Reverse ESD-protection diodes are internally connect-
ed between each analog signal pin, and both V+ and
V-. One of these diodes conducts if any analog signal
exceeds V+ or V-.
Virtually all of the analog leakage current is through the
ESD diodes to V+ or V-. Although the ESD diodes on a
given signal pin are identical and therefore fairly well
balanced, they are reverse biased differently. Each is
biased by either V+ or V- and the analog signal. This
means their leakages vary as the signal varies. The
dif-
ference in the two diode leakages from the signal path
to the V+ and V- pins constitutes the analog-signal-path
leakage current. All analog leakage current flows to the
supply terminals, not to the other switch terminal. This
explains how both sides of a given switch can show
leakage currents of either the same or opposite polarity.
There is no connection between the analog-signal paths
and GND. The analog-signal paths consist of an N-
channel and P-channel MOSFET with their sources and
drains paralleled and their gates driven out-of-phase to
V+ and V- by the logic-level translators.
V+ and GND power the internal logic and logic-level
translator and set the input logic threshold. The logic-
level translator converts the logic levels to switched V+
and V- signals to drive the analog switches’ gates. This
drive signal is the only connection between GND and
the analog supplies. V+ and V- have ESD-protection
diodes to GND. The logic-level input has ESD protec-
tion to V+ and to V- but not to GND, so the logic signal
can go below GND (as low as V-) when bipolar sup-
plies are used.
Increasing V- has no effect on the logic-level thresholds,
but it does increase the drive to the internal P-channel
switches, reducing the overall switch on-resistance. V-
also sets the negative limit of the analog-signal voltage.
The logic-level input pin, IN, has ESD-protection diodes
to V+ and V- but not to GND, so it can be safely driven
to V+ and V-. The logic-level threshold, VIN, is CMOS/
TTL compatible when V+ is between 4.5V and 36V
(see
Typical Operating Characteristics).
Bipolar Supplies
The MAX4526/MAX4527 operate with bipolar supplies
between ±4.5V and ±18V. However, since all factory
characterization is done with ±15V supplies, specifica-
tions at other supplies are not guaranteed. The V+ and
V- supplies need not be symmetrical, but their sum
cannot exceed the absolute maximum rating of 44V
(see
Absolute Maximum Ratings).
MAX4526/MAX4527
Phase-Reversal Analog Switches
_______________________________________________________________________________________
7
A
TIME WAVEFORMS
OUTPUT SPECTRUM
MODULATOR/DEMODULATOR CIRCUIT
LOGIC (CARRIER)
LOGIC
(CARRIER)
INPUT
OUTPUT
IN
B
A
X
Y
GND
V+
V-
V+
FREQUENCY
AMPLITUDE
LOWER
SIDEBAND
UPPER
SIDEBAND
SUPPRESSED CARRIER
B
X
Y
X-Y
(OUTPUT)
MAX4526
MAX4527
Figure 2. Balanced Modulator/Demodulator
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J6D-IW-F2 | CONVERTER MOD DC/DC 85V 100W |
| VI-BWX-IY-F3 | CONVERTER MOD DC/DC 5.2V 50W |
| MAX4066CSD+ | IC SWITCH QUAD SPST 14SOIC |
| P87C58X2BN,112 | IC 80C51 MCU 256 RAM 40DIP |
| VE-J64-IW-F4 | CONVERTER MOD DC/DC 48V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4527CUA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4527CUA+ | 功能描述:模擬開關 IC Phase-Reversal Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4527CUA+T | 功能描述:模擬開關 IC Phase-Reversal Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4527CUA-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4527EPA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。