- 您現在的位置：買賣IC網 > PDF目錄5513 > MAX4430ESA+T (Maxim Integrated Products)IC OP AMP SGL 180MHZ 8-SOIC PDF資料下載
參數資料
| 型號： | MAX4430ESA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OP AMP SGL 180MHZ 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 轉換速率： | 100 V/µs |
| -3db帶寬： | 180MHz |
| 電流 - 輸入偏壓： | 11µA |
| 電壓 - 輸入偏移： | 1250µV |
| 電流 - 電源： | 11mA |
| 電流 - 輸出 / 通道： | 60mA |
| 電壓 - 電源，單路/雙路(±)： | 9 V ~ 11 V，±4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
Detailed Description
The MAX4430–MAX4433 are wide-bandwidth, ultra-low-
distortion, voltage-feedback amplifiers. The MAX4430/
MAX4432 are internally compensated for unity gain.
The MAX4431/MAX4433 are internally compensated for
gains of +2V/V or greater.
These amplifiers have ultra-fast 37ns (MAX4430/
MAX4432) 16-bit settling times, 100dB SFDR at 1MHz,
and 4Vp-p output swing with minimum 110dB open-
loop gain.
High-Speed ADC Input Driver Application
The MAX4430–MAX4433 op amps are ideal for driving
high-speed 14- to 16-bit ADCs. In most cases, these
ADCs operate with a charge balance scheme, with
capacitive loads internally switched on and off from the
input. The driver used must withstand these changing
capacitive loads while holding the signal amplitude sta-
bility consistent with the ADC’s resolution and, at the
same time, have a frequency response compatible with
the sampling speed of the ADC (Figure 1).
Inverting and Noninverting Configurations
The circuits typically used for the inverting and non-
inverting configurations of the MAX4430–MAX4433 are
shown in Figures 2a and 2b. The minimum uncondition-
ally stable gain values are 1 for the MAX4430/MAX4432
and 2 for the MAX4431/MAX4433. Use care in selecting
the value for the resistor marked RS in both circuits.
From dynamic stability considerations (based on the
part’s frequency response and the input capacitance of
the MAX4430–MAX4433), the maximum recommended
value for RS is 500
. In general, lower RS values will
yield a higher bandwidth and better dynamic stability,
at the cost of higher power consumption, higher power
dissipation in the IC, and reduced output drive avail-
ability. For a minimum RS value, take into consideration
that the current indicated as IF is supplied by the output
stage and must be discounted from the maximum out-
put current to calculate the maximum current available
to the load. IF can be found using the following equa-
tion:
IF = VIN(MAX) / RS
If DC thermal stability is an important design concern,
the Thevenin resistance seen by both inputs at DC
must be balanced. This includes the resistance of the
signal source and termination resistors if the amplifier
signal input is fed from a transmission line. The capaci-
tance associated with the feedback resistors must also
be considered as a possible limitation to the available
bandwidth or to the dynamic stability. Only resistors
with small parallel capacitance specifications should
be considered.
Applications Information
Layout and Power-Supply Bypassing
The MAX4430–MAX4433 have wide bandwidth and
consequently require careful board layout. To realize
the full AC performance of these high-speed amplifiers,
pay careful attention to power-supply bypassing and
board layout. The PC board should have a large low-
impedance ground plane that is as free of voids as
possible. Do not use commercial breadboards. Keep
signal lines as short and straight as possible. Observe
high-frequency bypassing techniques to maintain the
MAX4430–MAX4433
Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
_______________________________________________________________________________________
9
+VCC
-VEE
HIGH-SPEED
14/16-BIT ADC
Figure 1. Typical Application Circuit
VOUT
VIN
RS
RF
IF
RF
RS
VOUT
VIN
=
A = 1 +
Figure 2a. Noninverting Configuration
- RF
RS
VOUT
VIN
VOUT
VIN
RB
RF
RS
IF
=
A =
Figure 2b. Inverting Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| 6469105-2 | VERT HDR W/LTCH 3.8MMPOST LNTH |
| 532436-2 | CONN HDI PLUG 120POS 4ROW VERT |
| MAX412BESA+T | IC OPAMP LN LV PREC 28MHZ 8-SOIC |
| 5223524-4 | 2MMFB,5R,ASY,120,SIG,HDR,EN |
| MAX409BEPA+ | IC OP AMP SINGLE SS 8-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4430EUK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4430EUK+ | 制造商:Maxim Integrated Products 功能描述:OP AMP SGL GP 5.5V 5PIN SOT-23 - Rail/Tube |
| MAX4430EUK+T | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4430EUK-T | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4431ESA | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。