- 您現在的位置：買賣IC網 > PDF目錄5525 > MAX4354ESD+ (Maxim Integrated Products)IC OP AMP R-R SS 14-SOIC PDF資料下載
參數資料
| 型號： | MAX4354ESD+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/19頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R SS 14-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 4 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 240 V/µs |
| -3db帶寬： | 80MHz |
| 電流 - 輸入偏壓： | 800nA |
| 電壓 - 輸入偏移： | 400µV |
| 電流 - 電源： | 620µA |
| 電流 - 輸出 / 通道： | 22mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/MAX4354
Low-Cost, +3V/+5V, 620A, 200MHz,
Single-Supply Op Amps with Rail-to-Rail Outputs
______________________________________________________________________________________
11
Detailed Description
The MAX4452/MAX4352 single, MAX4453/MAX4353
dual, and MAX4454/MAX4354 quad, single-supply, rail-
to-rail, voltage-feedback amplifiers achieve high slew
rates and wide bandwidths while consuming only
620A per amplifier. Excellent speed/power ratio
makes them ideal for portable devices and high-fre-
quency signal applications.
Internal feedback around the output stage ensures low
open-loop output impedance, reducing gain sensitivity
to load variations. This feedback also produces
demand-driven current bias to the output transistors.
Rail-to-Rail Outputs, Ground-Sensing Input
The input common-mode range extends from (VEE -
0.1V) to (VCC - 1.5V) with excellent common-mode
rejection. Beyond this range, the amplifier output is a
nonlinear function of the input, but does not undergo
phase reversal or latchup.
The output swings to within 180mV of either power-sup-
ply rail with a 1k
load. The input ground-sensing and
the rail-to-rail output substantially increase the dynamic
range.
Output Capacitive Loading and Stability
The MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/
MAX4354 are optimized for AC performance. They are
not designed to drive highly reactive loads. Such loads
decrease phase margin and may produce excessive
ringing and oscillation. The use of an isolation resistor
eliminates this problem (Figure 1). Figure 2 is a graph
of the Optimal Isolation Resistor (RISO) vs. Capacitive
Load.
Applications Information
Choosing Resistor Values
Unity-Gain Configuration
The MAX4452/MAX4453/MAX4454 are internally com-
pensated for unity gain. When configured for unity gain,
a 24
feedback resistor (RF) is recommended. This
resistor improves AC response by reducing the Q of
the parallel LC circuit formed by the parasitic feedback
capacitance and inductance.
Inverting and Noninverting Configurations
Select the gain-setting feedback (RF) and input (RG)
resistor values that best fit the application. Large resis-
tor values increase voltage noise and interact with the
amplifier’s input and PC board capacitance. This can
generate undesirable poles and zeros and decrease
bandwidth or cause oscillations. For example, a nonin-
verting gain-of-two configuration (RF = RG) using 1k
resistors, combined with 2pF of amplifier input capaci-
tance and 1pF of PC board capacitance, causes a pole
at 106MHz. Since this pole is within the amplifier band-
width, it jeopardizes stability. Reducing the 1k
resis-
tors to 100
extends the pole frequency to 1.06GHz,
but could limit output swing by adding 200
in parallel
with the amplifier’s load resistor.
Note: For high-gain applications where output offset
voltage is a consideration, choose RS to be equal to
the parallel combination of RF and RG (Figures 3a and
3b).
3b):
RS
RF RG
=
×
+
Figure 2. Optimal Isolation Resistor vs. Capacitive Load
VOUT
VIN
RBIN
RISO
RF
CL
RG
Figure 1. Driving a Capacitive Load Through an Isolation
Resistor
10
14
12
18
16
22
20
24
28
26
30
0
50
100
150
ISOLATION RESISTANCE
vs. CAPACITIVE LOAD
MAX4452/3/4
toc39
CLOAD (pF)
R
ISO
(
)
相關PDF資料 |
PDF描述 |
|---|---|
| 2-34151-1 | CONN RING 16-22 AWG #5/16 P-G |
| P6KE75HE3/54 | TVS 600W 75V 10% UNIDIR AXIAL |
| P6KE75CHE3/54 | TVS 600W 75V 10% BIDIR AXIAL |
| 1375798-1 | CONN PC/104-PLUS RCPT 120POS |
| P6KE75C-E3/54 | TVS 600W 75V 10% BIDIR AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4354ESD+ | 功能描述:高速運算放大器 3V/5V 620uA 200MHz Single-Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4354ESD+T | 功能描述:高速運算放大器 3V/5V 620uA 200MHz Single-Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4354ESD-T | 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4354EUD | 功能描述:高速運算放大器 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4354EUD+ | 功能描述:高速運算放大器 3V/5V 620uA 200MHz Single-Supply RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。