- 您現在的位置：買賣IC網 > PDF目錄5549 > MAX4285EUT-T (Maxim Integrated Products)IC BUFF/AMP ADC 250MHZ SOT23-6 PDF資料下載
參數資料
| 型號： | MAX4285EUT-T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BUFF/AMP ADC 250MHZ SOT23-6 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 緩沖器 |
| 電路數： | 1 |
| 轉換速率： | 385 V/µs |
| -3db帶寬： | 220MHz |
| 電流 - 輸入偏壓： | 13µA |
| 電壓 - 輸入偏移： | 1500µV |
| 電流 - 電源： | 23mA |
| 電流 - 輸出 / 通道： | 106mA |
| 電壓 - 電源，單路/雙路(±)： | 2.85 V ~ 6.5 V，±1.425 V ~ 3.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-6 |
| 包裝： | 帶卷 (TR) |
MAX4285–MAX4288/MAX4387
/MAX4388
+3V/+5V, 250MHz, SOT23 ADC Buffer Amplifiers
with High-Speed Disable
12
______________________________________________________________________________________
RG
RF
RS
CI
MAX4285
MAX4286
MAX4287
MAX4288
MAX4387
MAX4388
Figure 1. Using an Isolation Resistor (RS ) for High Capacitive
Loads
For example, a noninverting gain-of-two configuration
(RF = RG) using 1k
resistors, combined with 2pF typi-
cal amplifier input capacitance, generates a pole at
159MHz. Since this pole is within the amplifier band-
width, it jeopardizes stability. Reducing these 1k
resistors to 100
extends the pole frequency to
1.59GHz, but affects output swing by adding 200
in
parallel with the amplifier’s load resistor. The typical
value for RF is 300
.
Layout and Power-Supply Bypassing
These amplifiers operate from a single +2.85V to +6.5V
power supply or from ±1.425V to ±3.25V dual supplies.
For single-supply operation, bypass VCC to ground with
a 0.1nF capacitor as close to the pin as possible, with a
0.1F capacitor in parallel. If operating with dual sup-
plies, bypass each supply with capacitors to ground.
Observe the following guidelines:
A solid ground plane is essential for good high-fre-
quency behavior.
Where possible, use multiple ground vias.
Use a PC board with at least two layers. Avoid
areas of unreferenced copper-clad.
Keep signal traces as short and as straight as pos-
sible. Do not make sharp turns; round all trace
corners.
Use a constant-impedance board design if possi-
ble.
High-Speed Disable
The MAX4285/MAX4286/MAX4288 and MAX4388 fea-
ture a disable (DISABLE_) input that places the amplifi-
er in a low-power, high-output-impedance state. When
DISABLE_ is asserted, the amplifier’s output impedance
is typically 35k
. This high output impedance, com-
bined with the low 2pF output capacitance, make these
devices ideal for ADC input multiplexing applications or
switch applications. Typical enable/disable times are
40ns/50ns.
Output Capacitive Loading and Stability
These op amps are optimized for AC performance.
They are not designed to drive highly reactive loads,
which decrease phase margin and may produce
excessive ringing and oscillation. A small isolation
resistor (usually 20
to 30) placed before the reactive
load reduces possible ringing and oscillation (Figure
1). At higher capacitive loads, AC performance is
dependent on the interaction of the load capacitance,
the isolation resistor, and on-board layout.
Output Drive Capability
The MAX4285–MAX4288 and MAX4387/MAX4388 have
an output sink capability of 106mA and a source capa-
bility of 77mA. This high current ability allows them to
drive low-impedance and dynamic-impedance ADC
inputs. The linear output range of these devices is (VEE
+ 0.4V) to (VCC - 0.4V). Operation beyond this range is
not recommended due to reduced gain and phase
margin.
相關PDF資料 |
PDF描述 |
|---|---|
| 160887-2 | CONN UNINS TAB 17-20AWG 0.110 |
| MNGI14-250DFX-BOTTLE | CONN FMAL DISCONN 16-14AWG 100PC |
| TLV2264INE4 | IC OPAMP GP R-R 710KHZ 14DIP |
| EL2228CSZ | IC OPAMP DUAL LOW NOISE 8-SOIC |
| HA7-2520-2 | IC OPAMP 20MHZ 120V/US 8-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4286ESA | 功能描述:高速運算放大器 3V/5V 250MHz ADC Buffer Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4286ESA+ | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4286ESA+T | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4286ESA-T | 功能描述:高速運算放大器 3V/5V 250MHz ADC Buffer Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4286EUT | 制造商:Maxim Integrated Products 功能描述:+3V/+5V 250MHZ SOT23 ADC BUFFER A - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。