- 您現在的位置：買賣IC網 > PDF目錄3343 > MAX4249ESD+T (Maxim Integrated Products)IC OP AMP R-R LN 14-SOIC PDF資料下載
參數資料
| 型號： | MAX4249ESD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/16頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R LN 14-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 推挽式，滿擺幅 |
| 轉換速率： | 2.1 V/µs |
| 增益帶寬積： | 22MHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 70µV |
| 電流 - 電源： | 420µA |
| 電流 - 輸出 / 通道： | 68mA |
| 電壓 - 電源，單路/雙路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
UCSP, Single-Supply, Low-Noise,
Low-Distortion, Rail-to-Rail Op Amps
10
Maxim Integrated
MAX4249–MAX4257
Low Distortion
Many factors can affect the noise and distortion that the
device contributes to the input signal. The following
guidelines offer valuable information on the impact of
design choices on Total Harmonic Distortion (THD).
Choosing proper feedback and gain resistor values for
a particular application can be a very important factor
in reducing THD. In general, the smaller the closed-
loop gain, the smaller the THD generated, especially
when driving heavy resistive loads. Large-value feed-
back resistors can significantly improve distortion. The
THD of the part normally increases at approximately
20dB per decade, as a function of frequency.
Operating the device near or above the full-power
bandwidth significantly degrades distortion.
Referencing the load to either supply also improves the
part’s distortion performance, because only one of the
MOSFETs of the push-pull output stage drives the out-
put. Referencing the load to midsupply increases the
part’s distortion for a given load and feedback setting.
(See the Total Harmonic Distortion vs. Frequency graph
in the
Typical Operating Characteristics.)
For gains # 10V/V, the decompensated devices
MAX4249/MAX4255/MAX4256/MAX4257 deliver the
best distortion performance, since they have a higher
slew rate and provide a higher amount of loop gain for
a given closed-loop gain setting. Capacitive loads
below 400pF, do not significantly affect distortion
results. Distortion performance remains relatively con-
stant over supply voltages.
Low Noise
The amplifier’s input-referred, noise-voltage density is
dominated by flicker noise at lower frequencies, and by
thermal noise at higher frequencies. Because the ther-
mal noise contribution is affected by the parallel combi-
nation of the feedback resistive network (RF || RG,
Figure 1), these resistors should be reduced in cases
where the system bandwidth is large and thermal noise
is dominant. This noise contribution factor decreases,
however, with increasing gain settings.
For example, the input noise-voltage density of the cir-
cuit with RF = 100k", RG = 11k" (AV = 10V/V) is en =
15nV/!Hz, en can be reduced to 9nV/!Hz by choosing
RF = 10k", RG = 1.1k" (AV = 10V/V), at the expense
of greater current consumption and potentially higher
distortion. For a gain of 100V/V with RF = 100k", RG =
1.1k", the en is low (9nV/!Hz).
CZ
RF
VOUT
VIN
RG
0
100mV
AV = 2V/V
RF = RG = 10kΩ
VIN =
50mV/div
VOUT =
100mV/div
2
s/div
0
100mV
AV = 2
RF = RG = 100kΩ
CZ = 11pF
50mV/div
100mV/div
VIN
VOUT
2
s/div
Figure 1. Adding Feed-Forward Compensation
Figure 2a. Pulse Response with No Feed-Forward
Compensation
Figure 2b. Pulse Response with 10pF Feed-Forward
Compensation
相關PDF資料 |
PDF描述 |
|---|---|
| 5VTP 3.15-R | FUSE 3.15A 250V TLAG IEC 5X20MM |
| N3440-D302RB | CONN HEADER STKD 30POS R/A LO |
| 81068-660C01-RB-WG | CONN HEADER 68POS STR LONG SMD |
| 81060-500203 | CONN HEADER 60POS R/A THRU HO |
| 532447-1 | HDI PIN ASSY 3 ROW 75 POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4249EUB | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4249EUB+ | 功能描述:運算放大器 - 運放 Low-Distortion Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4249EUB+T | 功能描述:運算放大器 - 運放 Low-Distortion Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4249EUB-T | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4250AAUK | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE/DISTORTION SINGLE-SUPPLY - Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。