- 您現在的位置：買賣IC網 > PDF目錄3319 > MAX4218ESD+T (Maxim Integrated Products)IC OP AMP R-R W/ENABLE 14SOIC PDF資料下載
參數資料
| 型號： | MAX4218ESD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OP AMP R-R W/ENABLE 14SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 3 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 600 V/µs |
| -3db帶寬： | 200MHz |
| 電流 - 輸入偏壓： | 5.4µA |
| 電壓 - 輸入偏移： | 4000µV |
| 電流 - 電源： | 5.5mA |
| 電流 - 輸出 / 通道： | 120mA |
| 電壓 - 電源，單路/雙路(±)： | 3.15 V ~ 11 V，±1.575 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
MAX4212/MAX4213/MAX4216/MAX4218/MAX4220
_______________Detailed Description
The MAX4212/MAX4213/MAX4216/MAX4218/MAX4220
are single-supply, rail-to-rail, voltage-feedback ampli-
fiers that employ current-feedback techniques to
achieve 600V/s slew rates and 300MHz bandwidths.
Excellent harmonic distortion and differential gain/
phase performance make these amplifiers an ideal
choice for a wide variety of video and RF signal-
processing applications.
The output voltage swing comes to within 50mV of each
supply rail. Local feedback around the output stage
assures low open-loop output impedance to reduce
gain sensitivity to load variations. This feedback also
produces demand-driven current bias to the output
transistors for ±100mA drive capability, while constrain-
ing total supply current to less than 7mA. The input
stage permits common-mode voltages beyond the nega-
tive supply and to within 2.25V of the positive supply rail.
__________Applications Information
Choosing Resistor Values
Unity-Gain Configuration
The MAX4212/MAX4213/MAX4216/MAX4218/MAX4220
are internally compensated for unity gain. When config-
ured for unity gain, the devices require a 24
resistor
(RF) in series with the feedback path. This resistor
improves AC response by reducing the Q of the parallel
LC circuit formed by the parasitic feedback capaci-
tance and inductance.
Inverting and Noninverting Configurations
Select the gain-setting feedback (RF) and input (RG)
resistor values to fit your application. Large resistor val-
ues increase voltage noise and interact with the amplifi-
er’s input and PC board capacitance. This can
generate undesirable poles and zeros and decrease
bandwidth or cause oscillations. For example, a nonin-
verting gain-of-two configuration (RF = RG) using 1k
resistors, combined with 1pF of amplifier input capaci-
tance and 1pF of PC board capacitance, causes a pole
at 159MHz. Since this pole is within the amplifier band-
width, it jeopardizes stability. Reducing the 1k
resis-
tors to 100
extends the pole frequency to 1.59GHz,
but could limit output swing by adding 200
in parallel
with the amplifier’s load resistor. Table 1 shows sug-
gested feedback, gain resistors, and bandwidth for
several gain values in the configurations shown in
Figures 1a and 1b.
Layout and Power-Supply Bypassing
These amplifiers operate from a single 3.3V to 11V power
supply or from dual supplies to ±5.5V. For single-supply
operation, bypass VCC to ground with a 0.1F capacitor
as close to the pin as possible. If operating with dual sup-
plies, bypass each supply with a 0.1F capacitor.
Miniature, 300MHz, Single-Supply,
Rail-to-Rail Op Amps with Enable
10
______________________________________________________________________________________
IN
RG
VOUT = [1+ (RF / RG)] VIN
RF
RTO
RTIN
RO
VOUT
IN
RG
VOUT = -(RF / RG) VIN
RF
RTO
RS
RTIN
RO
VOUT
Figure 1a. Noninverting Gain Configuration
Figure 1b. Inverting Gain Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| MAX407CSA+T | IC OP AMP DUAL SS 8-SOIC |
| LT6233CS6-10#TRM | IC OP AMP SGL 1.2MA R-R SOT23-6 |
| MAX412CSA+T | IC OPAMP LN LV PREC 28MHZ 8-SOIC |
| 532446-9 | HDI PIN ASSY 2 ROW 100 POS |
| P6KE20C-E3/54 | TVS 600W 20V 10% BIDIR AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4219EEE | 功能描述:高速運算放大器 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4219EEE+ | 功能描述:高速運算放大器 Closed-Loop Rail-Rail Buffer RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4219EEE+T | 功能描述:高速運算放大器 Closed-Loop Rail-Rail Buffer RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4219EEE-T | 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX4219ESD | 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。