- 您現在的位置：買賣IC網 > PDF目錄10834 > MAX4188ESD+T (Maxim Integrated Products)IC AMP CURRENT SENSE 14-SOIC PDF資料下載
參數資料
| 型號： | MAX4188ESD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CURRENT SENSE 14-SOIC |
| 標準包裝： | 2,500 |
| 應用： | 電流反饋 |
| 電路數： | 3 |
| -3db帶寬： | 200MHz |
| 轉換速率： | 350 V/µs |
| 電流 - 電源： | 1.5mA |
| 電流 - 輸出 / 通道： | 55mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 11 V，±2.25 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
MAX4188/MAX4189/MAX4190
Single/Triple, Low-Glitch, 250MHz, Current-
Feedback Amplifiers with High-Speed Disable
______________________________________________________________________________________
17
VOUT
RG
RS
VOUT = -(RF / RG) (VIN)
VIN
RF
RO
RT
MAX4188
MAX4189
MAX4190
Figure 3a. Inverting Gain Configuration
VOUT
RG
RS
VOUT = [1+ (RF / RG)] VIN
VIN
RF
RO
RT
MAX4188
MAX4189
MAX4190
Figure 3b. Noninverting Gain Configuration
Layout and Power-Supply Bypassing
As with all wideband amplifiers, a carefully laid out PCB
and adequate power-supply bypassing are essential to
realizing the optimum AC performance of MAX4188/
MAX4189/MAX4190. The PC board should have at
least two layers. Signal and power should be on one
layer. A large low-impedance ground plane, as free of
voids as possible, should be the other layer. With multi-
layer boards, locate the ground plane on a layer that
incorporates no signal or power traces.
Do not use wire-wrap boards or breadboards and
sockets. Wire-wrap boards are too inductive.
Breadboards and sockets are too capacitive. Surface-
mount components have lower parasitic inductance
and capacitance, and are therefore preferable to
through-hole components. Keep lines as short as pos-
sible to minimize parasitic inductance, and avoid 90°
turns. Round all corners. Terminate all unused amplifier
inputs to ground with a 100 or 150 resistor.
The MAX4188/MAX4189/MAX4190 achieve a high
degree of off-isolation (65dB at 10MHz) and low
crosstalk (-55dB at 10MHz). The input and output sig-
nal traces must be kept from overlapping to achieve
high off-isolation. Coupling between the signal traces of
different channels will degrade crosstalk. The signal
traces of each channel should be kept from overlap-
ping with the signal traces of the other channels.
Adequate bypass capacitance at each supply is very
important to optimize the high-frequency performance of
these amplifiers. Inadequate bypassing will also
degrade crosstalk rejection, especially with heavier
loads. Use a 1F capacitor in parallel with a 0.01F to
0.1F capacitor between each supply pin and ground to
achieve optimum performance. The bypass capacitors
should be located as close to the device as possible. A
10F low-ESR tantalum capacitor may be required to
produce the best settling time and lowest distortion
when large transient currents must be delivered to a
load.
Choosing Feedback and Gain Resistors
The optimum value of the external-feedback (RF) and
gain-setting (RG) resistors used with the MAX4188/
MAX4189/MAX4190 depends on the closed-loop gain
and the application circuit’s load. Table 1 lists the opti-
mum resistor values for some specific gain configura-
tions. One-percent resistor values are preferred to
maintain consistency over a wide range of production
lots. Figures 3a and 3b show the standard inverting
and noninverting configurations. Note that the nonin-
verting circuit gain (Figure 3b) is 1 plus the magnitude
of the inverting closed-loop gain. Otherwise, the two
circuits are identical.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4188EEE+T | IC AMP CURRENT SENSE 16-QSOP |
| JBXED0G02FCSDSR | CONN RCPT PROTRUDING 2POS CRIMP |
| MAX4190ESA+T | IC AMP CURRENT SENSE 8-SOIC |
| MAX4189ESD+T | IC AMP CURRENT SENSE 14-SOIC |
| MAX4258EUA+T | IC AMP VIDEO MUX 2CH 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4188EVKIT | 功能描述:放大器 IC 開發工具 RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX4189 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Triple, Low-Glitch, 250MHz, Current-Feedback Amplifiers with High-Speed Disable |
| MAX4189EEE | 功能描述:視頻放大器 RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4189EEE+ | 功能描述:視頻放大器 250MHz 1.5mA Current-Feedback RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4189EEE+T | 功能描述:視頻放大器 250MHz 1.5mA Current-Feedback RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。