- 您現在的位置：買賣IC網 > PDF目錄10832 > MAX4159EEE+T (Maxim Integrated Products)IC VIDEO MUX/AMP 2CH 16-QSOP PDF資料下載
參數資料
| 型號： | MAX4159EEE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/16頁 |
| 文件大小： | 0K |
| 描述： | IC VIDEO MUX/AMP 2CH 16-QSOP |
| 標準包裝： | 2,500 |
| 應用： | 2:1 多路復用器-放大器 |
| 電路數： | 1 |
| -3db帶寬： | 350MHz |
| 轉換速率： | 700 V/µs |
| 電流 - 電源： | 10.9mA |
| 電流 - 輸出 / 通道： | 100mA |
| 電壓 - 電源，單路/雙路(±)： | ±4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
MAX4158/MAX4159/MAX4258/MAX4259
350MHz/250MHz, 2-Channel
Video Multiplexer-Amplifiers
______________________________________________________________________________________
11
To realize the full AC performance of these high-speed
amplifiers, pay careful attention to power-supply
bypassing and board layout. The PC board should
have at least two layers: a signal and power layer on
one side, and a large, low-impedance ground plane on
the other side. The ground plane should be as free of
voids as possible, with one exception: the feedback pin
(FB) should have as low a capacitance to ground as
possible. This means that there should be no ground
plane under FB or under the components (RF and RG)
connected to it. With multilayer boards, locate the
ground plane on a layer that incorporates no signal or
power traces.
Regardless of whether or not a constant-impedance
board is used, it is best to observe the following guide-
lines when designing the board:
1) Do not use wire-wrap boards (they are much too
inductive) or breadboards (they are much too
capacitive).
2) Do not use IC sockets. IC sockets increase reac-
tances.
3) Keep lines as short and as straight as possible. Do
not make 90° turns; round all corners.
4) Observe high-frequency bypassing techniques to
maintain the amplifier’s accuracy and stability.
5) Bear in mind that, in general, surface-mount compo-
nents have shorter bodies and lower parasitic reac-
tance, giving much better high-frequency
performance than through-hole components.
The bypass capacitors should include a 10nF ceramic
surface-mount capacitor between each supply pin and
the ground plane, located as close to the package as
possible. Optionally, place a 10F tantalum capacitor at
the power-supply pins’ points of entry to the PC board
to ensure the integrity of incoming supplies. The power-
supply trace should lead directly from the tantalum
capacitor to the V+ and V- pins. To minimize parasitic
inductance, keep PC traces short and use surface-
mount components.
Ground pins have been placed between input channels
to minimize crosstalk between the two input channels.
(The grounds extend inside the package all the way to
the silicon.) These pins should be connected to a com-
mon ground plane on the PC board.
Input termination resistors and output back-termination
resistors, if used, should be surface-mount types, and
should be placed as close to the IC pins as possible.
Choosing Feedback
_________________and Gain Resistors
As with all current-mode feedback amplifiers, the fre-
quency response of the MAX4158/MAX4159/MAX4258/
MAX4259 is critically dependent on the value of the
feedback resistor RF. RF, in conjunction with an internal
compensation capacitor, forms the dominant pole in the
feedback loop. Reducing RF’s value increases the pole
frequency and the -3dB bandwidth, but also increases
peaking due to interaction with other nondominant
poles. Increasing RF’s value reduces peaking and
bandwidth.
Tables 1 and 2 show optimal values for the feedback
resistor (RF) and gain-setting resistor (RG) for all parts.
Note that the MAX4258/MAX4259 offer superior AC per-
formance for all gains except unity gain (0dB). These
values provide optimal AC response using surface-
mount resistors and good layout techniques. The
MAX4159/MAX4259 evaluation kit provides a practical
example of such layout techniques.
Stray capacitance at FB causes feedback resistor
response curve. Keep the capacitance at FB as low as
possible by using surface-mount resistors, and avoid-
ing the use of a ground plane beneath or beside these
resistors and the FB pin. Some capacitance is unavoid-
able; if necessary, its effects can be counteracted by
adjusting RF. 1% resistors are recommended to main-
tain consistency over a wide range of production lots.
Table 1. MAX4158/MAX4159 Bandwidth
and Gain vs. Gain-Setting Resistors
200
110
2
6
110
5
14
80
12
40
6
32.5
130
14.5
10
20
130
-3dB BW
(MHz)
0.1dB BW
(MHz)
RG
(
)
RF
(
)
GAIN
350
100
∞
430
1
0
(dB)
(V/V)
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BTK-IV-S | CONVERTER MOD DC/DC 40V 150W |
| MAX4159EEE+ | IC VIDEO MUX/AMP 2CH 16-QSOP |
| VI-BTJ-IV-S | CONVERTER MOD DC/DC 36V 150W |
| MAX4159ESD+ | IC VIDEO MUX/AMP 2CH 14-SOIC |
| MAX5886EGK+TD | IC DAC 12BIT 3.3V 500MSPS 68-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4159ESD | 功能描述:視頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4159ESD+ | 功能描述:視頻放大器 350/250MHz 2Ch Video MUX-Amplifier RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4159ESD+T | 功能描述:視頻放大器 350/250MHz 2Ch Video MUX-Amplifier RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4159ESD-T | 功能描述:視頻放大器 RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX4159EVKIT | 功能描述:放大器 IC 開發工具 Programmers, Development Systems RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。